Re: Motor mounts
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Motor mounts



I received the mitymounts. They appear to be OEM mounts with two large screws added to the 
drivers side mount turning it into a solid mount for the most part. The head of the screw is countersunk into the body side steel plate of the mount. The shank end of the screw is tack welded onto the engine side steel plate of the mount. The passenger side mount has no apparent modifications. They appear to be identical to the mounts I purchased for $29.99 a pair without the two screws. The pictures are of the mitymounts. In the first picture the mount marked driver's side. I'm pointing to the weld marks where the screws shank are attached. The other screws weld marks are under hidden under the drivers side sticker. The second picture down is of the counter sunk heads of the screws on the same mount. Next picture is a side view of the drivers side mount showing the screw heads. The last picture is of the passenger side mount. The mounts came with the labels. They also came with a form requesting personal information. The VIN number year make and model of the vehicle they are going to be installed on. They have a life time warranty. The engine has to be stock and not exceed 120% of their original factory rated horse power. The registration must be completed within 30 days and is not transferable to a new owner. The mount will be replaced no other damages will be covered. 
image1.jpegimage2.jpegimage4.jpegimage3.jpeg

Sent from my iPhone

On Jul 6, 2017, at 14:26, mike creglow <mcreglow@xxxxxxxxx> wrote:

steve,

you broke poly-lock motor mounts?  wow.
i'm curious when your pinion yoke broke if that caused the mounts to break with your drive shaft flailing about at speed.  if that is the case i would check your trans mount also.
i see a torque strap in your future.


mike

On Thu, Jul 6, 2017 at 1:30 AM, MO <micher@xxxxxxxxxxxxxxx> wrote:
Today, I find that I have a separated motor mount on the left and a  right one that is torn. These were in the Schumacker  big block into a 318 K frame kit.  I have had them for about three-four  years, and very few miles last Fall and so far this year.  I admit, I was abuseing them  with a few  " launches"  Schumacker does not have the mounts in stock and I see they are out of stock on about all motor mounts. It appears they are made by Imperial Services.  I do not want the Chinese made ones. I found a pair of OEM  motor mount isolators on e-bay.  Doesn't that mean, made by the company that supplied Mopar and therefore made in USA? 
 With the issues mentioned in this thread, I don't think I want to try expensive polyurathane or lock type mounts , nor solid mounts.  So, I am going with the stock mounts and the Schumacker torque "strap" ........................MO


--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.