RE: valve springs
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: valve springs



MO,
	There are a few different types of spring compressors available -
the generic screw type requires a lot of twisting that's hard on fingers.
Mancini has a lever type that requires bolting the rocker shaft on for each
valve, but works well.

	A 62-65 guy -  I can't remember his last name right now but I think
his first was Mike, had a nice '64 Sport Fury IIRC - developed a really nice
one a few years back.  It's available from Mancini - a little pricey but
well worth the price if you're going to do it more than once.  It can be
used on the engine, without removing the stamped rockers (not sure about
others).  Has a screw to crank the spring down that can be run with an
impact wrench or cordless driver.  Next time I have to change springs on the
motor I'll have one.

http://chucker54.stores.yahoo.net/abenvaspto.html

SC 

-----Original Message-----
From: MO ( Steve Mick) [mailto:micher@xxxxxxxxxxxxxxx] 
Sent: Wednesday, October 27, 2010 8:30 PM
To: 1962to1965mopars@xxxxxxxxxx
Subject: Re: valve springs


OK Thanks Darwin for sending the pic of the valve spring tool.  With that
and the other replys the idea sinks in.. Roger, I would guess the rope trick
is to feed in thru the spark plug hole when the piston is below TDC and then
turn over the crank untill the rope makes contact with the valves?  Thanks
folks, I can now go to sleep tonight!..........................MO
{Steve Mick}
http://stevemick.shutterfly.com/pictures#Part%202
----- Original Message -----
From: "MO ( Steve Mick)" <micher@xxxxxxxxxxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Wednesday, October 27, 2010 6:52 PM
Subject: Re: valve springs


>
> Common now, Don't mess with the feeble minded!!! what valve spring 
> compressor?....................MO {Steve Mick}
> http://stevemick.shutterfly.com/pictures#Part%202
> ----- Original Message -----
> From: "65" <65Val@xxxxxxxxx>
> To: <1962to1965mopars@xxxxxxxxxx>
> Sent: Wednesday, October 27, 2010 6:35 PM
> Subject: Re: valve springs
>
>
>>
>>
>> Yessir! Same procedure. Use this valve spring compressor....
>>
>>
>>
>> Darwin/BC Canada
>> '67 Dart GT 'vert - 273/904
>> http://s41.photobucket.com/albums/e285/65val/
>>
>> ----- Original Message -----
>> From: "MO ( Steve Mick)" <micher@xxxxxxxxxxxxxxx>
>> To: <1962to1965mopars@xxxxxxxxxx>
>> Sent: Wednesday, October 27, 2010 4:27 PM
>> Subject: valve springs
>>
>>
>>>
>>> Tech question--On a chebrolay you can change valve springs without 
>>> removing the heads by using a simple tool. and air pressure in the 
>>> cylinder to keep the valves closed. ---Is there a way to change 
>>> valve springs without removing the heads in a Mopar 440 engine?  
>>> Thanks for any help................................MO
>>> {Steve Mick}
>>> http://stevemick.shutterfly.com/pictures#Part%202
>>>
>>> ----
>>> Please address private mail -- mail of interest to only one person 
>>> -- directly to that person.  I.e., send parts/car transactions and 
>>> negotiations as well as other personal messages only to the intended 
>>> recipient, not to the Clubhouse public address. This practice will 
>>> protect your privacy, reduce the total volume of mail and fine tune 
>>> the content signal to Mopar topic.  Thanks!
>>>
>>> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
>>> http://www.1962to1965mopar.ornocar.org/mletiq.html and
>>>
>>
>> [Non-text portions of this message have been removed]
>>
>>
>> ----
>> Please address private mail -- mail of interest to only one person -- 
>> directly to that person.  I.e., send parts/car transactions and 
>> negotiations as well as other personal messages only to the intended 
>> recipient, not to the Clubhouse public address. This practice will 
>> protect your privacy, reduce the total volume of mail and fine tune 
>> the content signal to Mopar topic.  Thanks!
>>
>> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
>> http://www.1962to1965mopar.ornocar.org/mletiq.html and
>>
>>
>
>
> ----
> Please address private mail -- mail of interest to only one person -- 
> directly to that person.  I.e., send parts/car transactions and 
> negotiations as well as other personal messages only to the intended 
> recipient, not to the Clubhouse public address. This practice will 
> protect your privacy, reduce the total volume of mail and fine tune 
> the content signal to Mopar topic.  Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and
>
>
> 


----
Please address private mail -- mail of interest to only one person --
directly to that person.  I.e., send parts/car transactions and negotiations
as well as other personal messages only to the intended recipient, not to
the Clubhouse public address. This practice will protect your privacy,
reduce the total volume of mail and fine tune the content signal to Mopar
topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and
http://www.1962to1965mopar.ornocar.com/general_disclaimer.html. 


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html. 














Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.