RE: Fine tuning

[ledman_70@xxxxxxxxxxx]

[AD removed for archives]
-------------------------------------------------------------------
Ben & Jerry?s® or Häagen-Dazs®?
Take our Nationwide Ice Cream Survey today! Receive a FREE* $100 
Restaurant Gift Card of your choice or $100 worth of Ben & 
Jerry?s® or Häagen-Dazs® ice cream for participating!
caadVYQbOyW3Na/Ice Cream Research Survey
-------------------------------------------------------------------

Well, THAT thought has only occurred to me a few hundred times, believe 
me! However, I have a 426 block all machined with new bearings and plugs 
waiting to go together this winter, so I'm just limping the 413 by till 
then. Of course, once the 426 is in, I will have to rebuild the 413 and 
find another car to put it in, won't I??? Then there's the 2 OTHER 413's 
sitting in the corner. hmmm..... ha ha
Jeff
Crabtree, William L LT NAVSTA MAYPORT, N1 wrote:
> 
> Jeff, I hate to say it and I'm sure you already know this but it looks 
> to me that you are pushing a rope with this setup. In other words, I 
> would stop at this point and rebuild that motor or you might be chasing 
> a lot of bugs before it's over with.
> 
> Bill,
> 
> -----Original Message-----
> From: ledman_70@xxxxxxxxxxx [mailto:ledman_70@xxxxxxxxxxx]
> Sent: Monday, September 26, 2005 13:31
> To: 1962to1965mopars@xxxxxxxxxx
> Subject: RE: Fine tuning
> 
> 
> [AD removed for archives]
> -------------------------------------------------------------------
> New Apple® iPod® nano. As Thin as a No. 2 Pencil. Stores up to 3 
> Days of Songs! Get it Here FREE*!
> caad0PFbP2uQLa/Superb Rewards 
> -------------------------------------------------------------------
> 
> Stock intake. I know it's not the best setup, but I haven't had time to 
> get an aluminum intake and install it yet. Seems to me with everything 
> else being new, it should all work. The engine is a 65 413 with over 
> 100k on it. Put a frresh set of stock heads on it last year, but the 
> rings are pretty worn, it smokes when it hit it hard. Compression is 
> 130-155lbs per cylinder. I know that's quite a variance, but it still 
> seems healthy enough to run good.
> Jeff
> Crabtree, William L LT NAVSTA MAYPORT, N1 wrote:
> > 
> > I looked that system up at Jegs and it's made by "Proform". That is a 
> > good middle of the road product name and that looks like a heck of a 
> > deal for that system. That looks like a lot of carb for a cast iron 
> > intake. Between that carb and the spacer there is sudden stop for air 
> > and fuel at the top of that intake. Is the intake ported? I would highly 
> > 
> > recommend a Performer RPM with that carb set at the factory settings. 
> > 
> > -----Original Message-----
> > From: ledman_70@xxxxxxxxxxx [mailto:ledman_70@xxxxxxxxxxx]
> > Sent: Monday, September 26, 2005 12:32
> > To: 1962to1965mopars@xxxxxxxxxx
> > Subject: RE: Fine tuning
> > 
> > 
> > [AD removed for archives]
> > -------------------------------------------------------------------
> > Need a new Cell Phone? A BlackBerry 7250 could be yours free! Find 
> > out how!
> > caadV2bbP2uQLa/Amazing phone
> > -------------------------------------------------------------------
> > 
> > No, it was a system made for Jegs, I don't remember the name. It came 
> > with distributor, harness, control box, and ballast resister for around 
> > $140. You think maybe something could be faulty in it?
> > Jeff
> > Jim Jablonski wrote:
> > > 
> > > Jeff,
> > > 
> > > IMHO, at that RPM, it sounds spark advance related.  What's the new 
> > > ignition system ... Mopar ECU/distributor?
> > > 
> > > Jim Jablonski
> > > Royal Oak, Michigan
> > > '64 Fury
> > > 
> > > ledman_70@xxxxxxxxxxx wrote:
> > > > 
> > > > I installed a new 780 Holley and complete new electronic ignition in my 
> > > > 413 in the last 2 months. I've rejetted the carb, changed the squirter, 
> > > > and adjusted the timing and carb till I'm blue in the face, but I can't 
> > > > get rid of the flat spot between 1500-1800 rpm. When you let the clutch 
> > > > out and the engine starts to load, that's where the flat spot is most 
> > > > obvious. If you take off agressively, it's invisible. The engine has a 
> > > > 509 Huhges cam, headers, and a 2" carb spacer to adapt the Holley to the 
> > > > 
> > > > 
> > > > 
> > > > 
> > > > original cast intake. I can't determine what's causing the flat spot, so 
> > > > 
> > > > 
> > > > 
> > > > 
> > > > I don't know which direction to go from here...any ideas??? Bueller? 
> > > > Bueller?
> > > > 
> > > > Jeff Adams
> > > > 64 Polara
> > 
> > 
> > 
> > Jeff Adams
> > 64 Polara
> > 
> > [AD removed for archives]
> > -------------------------------------------------------------------
> > New Apple® iPod® nano. As Thin as a No. 2 Pencil. Stores up to 3 
> > Days of Songs! Get it Here FREE*!
> > caad0PFbP2uQLf/Superb Rewards 
> > -------------------------------------------------------------------
> > 
> > ----
> > Please address private mail -- mail of interest to only one person -- 
> > directly to that person.  I.e., send parts/car transactions and 
> > negotiations as well as other personal messages only to the intended 
> > recipient, not to the Clubhouse public address. This practice will 
> > protect your privacy, reduce the total volume of mail and fine tune the 
> > content signal to Mopar topic.  Thanks!
> > 
> > '62 to '65 Mopar Clubhouse Discussion Guidelines:
> > http://www.1962to1965mopar.ornocar.org/mletiq.html. 
> 
> 
> 
> Jeff Adams
> 64 Polara
> 
> [AD removed for archives]
> -------------------------------------------------------------------
> Is your computer freezing up or slowing down?
> Repair corrupt files and harmful errors - protect your PC
> Take a 2-minute PC health check-up at no charge!
> caadVJEbP2uQLf/PC PowerScan
> -------------------------------------------------------------------
> 
> ----
> Please address private mail -- mail of interest to only one person -- 
> directly to that person.  I.e., send parts/car transactions and 
> negotiations as well as other personal messages only to the intended 
> recipient, not to the Clubhouse public address. This practice will 
> protect your privacy, reduce the total volume of mail and fine tune the 
> content signal to Mopar topic.  Thanks!
> 
> '62 to '65 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html. 



Jeff Adams
64 Polara

[AD removed for archives]
-------------------------------------------------------------------
Buying or Selling a Home? Get the Facts Before Buying or Selling! 
Get a FREE Home Valuation TODAY!
caadV2pbOyW3Nf/Home Valuation 
-------------------------------------------------------------------

----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 



bOyW3N.