The 62 has no setscrew or anything on the power window motor. The motor has
nothing but a little rubber coupling between it and the gearbox. A simple
strap holds it to the body, undo the strap and remove the motor...takes
longer to get to it than it does to remove it.
Most of the motors in the 62 and 63s I have encountered were Prestolite
made, very simple in construction. A plain bushing at the drive end,
brushes in the other end. Two thru bolts hold it all together. Simply
scribe a line on all 3 main pieces before removing the thru bolts, then
remove the bolts, remove the drive end ( shaft end ) and remove the armature
out the drive direction. You may have to wiggle things a bit, you can slip
the commutator end out a bit and that will help you keep an eye on the
brushes and brush springs, but they are usually gummed up anyway.
There are small washers/ shims at each end of the armature, at each end
plate...just make sure you put them at the same end they came out of. As
soon as you remove the end plates you will see them, or as you remove the
end plate at the drive end and the armature will have them on the other end
when you remove it.
Once the armature and drive end are out, the commutator end plate and main
body with the field coils are left. It is usually not necessary or
advisable in most cases to desolder the drive end from the main body but it
is possible. 90 percent of the motors I have taken apart needed the
commutator ends cleaned, the brushes cleaned and in general just a good
cleaning and some tlc.
I have found that chucking the armature in a drill, and using commutator
paper ( a form of abrasive cloth ) will get you there nearly every time. In
some serious cases where the brushes left a deep impression in the armature
I held a small fine file against the commutator only long enough to remove
the depression . ( Its actually a high spot from where the brushes never
wear that you remove ) Then follow up with commutator paper.
Once thats done, a good cleaning with a commercial spray electrical cleaner
or brakleen is next. Let dry thoroughly, and get a dab of suitable grease
on the bushings on each end...not too much on the commutator end or it will
get into the brushes. You can also take a very fine point file or similar
and clean the contact points in the commutator end plate, as they are a
thermal protection for the motor..if it stalls and the points get hot, they
open and halt current flow.
Now the fun part, you insert the armature in from the drive end, and you get
to put the brush springs and brushes down in the holder and then carefully
slide the commutator in between the brushes. Its not easy for the first 10
or so times, then you will discover a system that works best. I hold it in
one hand, use a long very thin driver to sneak the commutator over the
brushes in increments, then it will just slip right into place.
Install the drive end, tighten the thru bolts and youre done. I like to take
my drill and chuck the drive shaft into it again, and turn it each way a bit
before powering it up, helps reseat the brushes,. but those are seldom an
issue. I have never seen a motor yet with over half the brush worn away.
Go hook up a 12v ground to the case and alternately hook up 12v positive to
each power lead...but not at the same time ok. Its important to remember
the ground is thru the case and only one power lead gets 12v at a time.
Thats all there is to know about the 61-63 window motors. If you need help,
just email
Mikey
62 Crown Coupe
----------------- http://www.imperialclub.com -----------------
This message was sent to you by the Imperial Mailing List. Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm