I agree with a bead of silicone that's all I have ever used no leaks and never had a problem
On Thursday, January 1, 2015 3:24 PM, 65 <65val@xxxxxxxxx> wrote:
I've never had that problem. Just use enough
to fill the gap + a bit.
Darwin/BC Canada
'67 Dart GT'vert -
273/904...hibernating
'65 Cdn Valiant Custom 100'vert -
225/A833...SOLD!
----- Original Message -----
Sent: Thursday, January 01, 2015 11:51
AM
Subject: Re: Poly Intake Gasket End
Seals
No fear of the dreaded " silicone sheer off
the inside excess and wind up on your oil intake screen" ?? Nothing like
starting a debate at the first of the New Year 8-)
..........................MO
----- Original Message -----
Sent: Thursday, January 01, 2015 1:35
PM
Subject: Re: Poly Intake Gasket End
Seals
Agree as stated, just run a large bead of silicone/RTV on each rail, let it setup a bit, then install the intake.
After the RTV sets up completely, use a sharp utility knife to trim the
excess. Photos of both my cast Iron and aluminum manifold installed this
way. As far as the new CP manifold goes I have yet to hear from anyone who
has installed and run one on an engine. No reports on how they will
seal.
Nick T.
From:
"Bill M"
Subject: Re: Poly Intake Gasket End Seals
Ultimately the new CP wind tunnel poly manifold, but a Weiand
single plane may get put on briefly. The owner of Racer Brown Cams (Jim Dow)
wants to do a dyno comparison of the two manifolds on the same motor. He is
acquired a big batch of NOS manifolds and is now selling them. Since I was
intending to get my motor dynoed, I thought this would be a pretty neat
thing to do while I have the opportunity.
Bill M
On Jan 1, 2015 12:29 PM, <
furyus63@xxxxxxxxxxx> wrote:
Bill,
What manifold are you installing?
Nick T.
From:
"Bill M"
y1topbanana73@xxxxxxxxxSubject: Poly Intake
Gasket End Seals
Getting ready to install my new intake on my motor. When I set it on
with the main gaskets in place, the gap at the ends between the intake and
block is half the thickness of the end seals. The foam version will
compress just fine but will squeeze out unless glued down. The cork won't
squeeze out but I'm concerned about its ability to compress that much.
Any thoughts about using one vs the other?
Bill M
65 Coronet 500 'vert
http://goo.gl/6xUS173 Dart Sport, 05 Ram 2500 CTD,
4WD, QC, LB, Laramie
21 Model T Depot Hack, 06 Mazda
3
--
--
--
Please address private email -- email of interest
to only one person -- directly to that person. That is, email your parts/car
transactions and negotiations, as well as other personal messages, only to
the intended recipient. Do not just press "reply" and send your email to
everyone using the general '62-'65 Clubhouse public email address. This
practice will protect your privacy, reduce the total volume of mail and
fine-tune the content signal to Mopar topic. Thanks!
1962 to
1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html
and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google
Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
---
You received this message because you are subscribed to the Google
Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe
from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For
more options, visit https://groups.google.com/d/optout.
No virus found in this
message.
Checked by AVG -
www.avg.comVersion: 2015.0.5577 / Virus
Database: 4257/8851 - Release Date: 01/01/15
--
--
--
Please address private email -- email of interest
to only one person -- directly to that person. That is, email your parts/car
transactions and negotiations, as well as other personal messages, only to the
intended recipient. Do not just press "reply" and send your email to everyone
using the general '62-'65 Clubhouse public email address. This practice will
protect your privacy, reduce the total volume of mail and fine-tune the
content signal to Mopar topic. Thanks!
1962 to 1965 Mopar
Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html
and
http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups
"The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
---
You received this message because you are subscribed to the Google Groups
"The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from
this group and stop receiving emails from it, send an email to
1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For
more options, visit
https://groups.google.com/d/optout.
![]()
|
This email has been checked for viruses by Avast antivirus software.
www.avast.com
|
--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.
--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and
http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to
1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit
https://groups.google.com/d/optout.
Back to the Home of the Forward Look Network
