Re: Help with Bolt Removal
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Help with Bolt Removal



Good advice, lately though if I didn't have bad luck I wouldn't have any
luck.
Nico

On 07/24/2011 04:33 PM, Jimmy Peavy wrote:
> I don't think heat will solve your problem.
> What ever you do, do not use an eze-out.
> If you are able to use a lock nut, use a six point wrench to turn.
> I think you are only going to have luck drilling it out, but maybe
> you're a lucky guy?
>
> Jimmy
>
> On 7/24/2011 3:57 PM, Nico Over wrote:
>> Jimmy I agree the threads are galled up, If the heat doesn't do it I try
>> to rethread  and see if I can double nut it.
>> Thanks Nico
>>
>> On 07/24/2011 02:45 PM, Jimmy Peavy wrote:
>>> Is there enough sticking out that you can cut the head off, and run a
>>> die over the stud, screw on a nut, and another nut as a jam nut?
>>> If not using the scatter shield as a guide( guaranteeing a good
>>> center) cut the bolt off, and drill and re-tap the hole. Either retap
>>> to correct size, or re-tap using a helicoil.
>>> Stainless is famous for  galling up. Sounds like that's what it did.
>>>
>>>     Jimmy
>>>
>>> On 7/24/2011 3:16 PM, Nico Over wrote:
>>>> While putting my BB on a engine run in stand, I was bolting up the
>>>> scatter shield using stainless ARP bolts. One went in harder than the
>>>> rest (they were screwed in by hand) so I used a 1/4 drive ratchet
>>>> to get
>>>> this last one in. Now since it did not feel right I tried to back that
>>>> one out. It came out about half way and then locked up. I can turn
>>>> it in
>>>> but it will not come all the way out. I then managed to round the bolt
>>>> head so I decided to cut the head of with a air saw so I could get the
>>>> scatter shield off. I now have enough of the bolt left sticking out of
>>>> the block that I can get vice grips on it but it will not turn out.
>>>> I've
>>>> tried all sorts of penetrating oil to get it out but it locks up in
>>>> the
>>>> same place. I don't have the capability to weld a nut onto it since it
>>>> is stainless so I effectively now have two locating dowels on the left
>>>> side of the block. I know I can probably get away with this  but still
>>>> would like to get it out. Any ideas would be appreciated.
>>>> Nico Over
>>>> Va. Beach, Va.
>>>>
>

-- 
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.