Re: [Chrysler300] Shim Pack for '63-'64 300 Rear Axle

["Tim Tomlinson" <tomlin@xxxxxxxxx>]

Mark and group,
  The service manual for '64 says about setting the axle drive shaft end play "Where the original axle shafts and/or bearings are used, start the adjustment fo the axle end play with the original shim pack.  Use new styrofoam gaskets on each side of the shim packs."
  Now as to where to get shims--I was able to get what I needed about 12 years ago from an old Chrysler dealership.  However, now, I would start with those that specialize in MoPar drivlines.  Some suggestions:  Koller Dodge (Naperville, IL) ph: 630-355-3411.  IF they don't have what you need, ask if they know who may.  Another possibility:  MOPAR CITY, (Oregon, IL) 815-732-7751.  I have no experience with shims from these sources, just some ideas off the top of my head.
Tim Tomlinson
2X300-K
West Central IL
  ----- Original Message ----- 
  From: Mark Lindahl 
  To: chrysler300@xxxxxxxxxxxxxxx 
  Sent: Monday, November 10, 2008 5:32 PM
  Subject: Re: [Chrysler300] Shim Pack for '63-'64 300 Rear Axle


  Hi Again,

  The Service Manual does not mention any Axle flange gasket, but Napa and AutoZone show a gasket. Neither show shims are still available.
  http://www.autozone.com/R,125776/vehicleId,1829601/initialAction,partProductDetail/store,2567/partType,01948/shopping/partProductDetail.htm

  Can anyone tell me if the gasket came along later, perhaps as a fix? Or maybe this was used on 1965 and up?
  If the gasket is used, then the steel shims would be affected for the 0.013-0.018 inch axle end play.
  Any advice is welcome. My 300 is apart at the mechanic and he does not know whether to use the gasket along with the shims.

  Regards,
  Mark Lindahl

  ----- Original Message ----- 
  From: Mark Lindahl 
  To: chrysler300@xxxxxxxxxxxxxxx 
  Sent: Monday, November 10, 2008 3:53 PM
  Subject: [Chrysler300] Shim Pack for '63-'64 300 Rear Axle

  Hi All,

  Does anyone know how to obtain the following shims for the rear axle, '63-'64 300?
  I assume that a combination of these are used to get the correct 0.013-0.018 in. axle shaft end play?

  0.005 thick 2070866
  0.012 2070868
  0.030 2070870

  Thanks,
  Mark Lindahl
  '63 300 Conv.

  [Non-text portions of this message have been removed]

  [Non-text portions of this message have been removed]



   


------------------------------------------------------------------------------


  No virus found in this incoming message.
  Checked by AVG. 
  Version: 7.5.549 / Virus Database: 270.9.0/1780 - Release Date: 11/10/2008 8:58 PM


[Non-text portions of this message have been removed]


------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    mailto:Chrysler300-digest@xxxxxxxxxxxxxxx 
    mailto:Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/