Unless you are going for a perfect show
car, I would try Edelbrock aluminum heads They flow like crazy and are
straight bolt on!
Bob
From:
mailing-list-owner@xxxxxxxxxxxxxxxx
[mailto:mailing-list-owner@xxxxxxxxxxxxxxxx] On
Behalf Of Mike Becker
Sent: Saturday, December 17, 2005
5:57 AM
To: mailing-list@xxxxxxxxxxxxxxxx
Subject: RE: IML: Dick B's valves
I am going to revitalize the valve/seat thread with
a couple of questions/comments. recently while i have been deployed to
afghanistan some lowlife broke into my garage and stole my tools and various
parts like a holley fuel injection system for a 440, and in regards
to this thread a set of 67 915 heads, they had oversize because I thought this
was best) stainless valves, bronze guides, and hardened seats. my question:
these heads cameoff a 67 300, (all 67 440's supposedly came with 915 heads,
small chanber, large ex valve) when i rebuilt my 67 yellow vert it had 516
heads, small combustion chamber and small (1.60 ex valve) which are
supposed to be 361-383-413 truck heads. I thought it was a factory
mistake.(maybe?) was it an anomly that they were on my vert engine or was
that the way imperial s were for 67 ? (the engine had never been
apart before) I understand what dick is saying, when i replace these
stolen heads, For best performance , do i want 67 small ex haust valve heads or
or the 915's with the larger ex. valves ? The small combution chambers are a no
brainer as the give a more active combustion and allow a higher c/r without
detonation. as 400 heads not needing hardened seats, i have heard this
before and always belived it, but last summer I took a set of heads off a
400 that i had run on uleaded gas for a few years, and they had valve recession
big time, so if I am going to put some money into some heads I am thinking
some 67 heads with hardened seat my be the best . What do you guys think?
thanks, mike becker
Dick Benjamin
<dickb@xxxxxxxxx> wrote:
I appreciate all the suggestions for
“improved heads” you folks are making to me, but I wouldn’t
consider changing from the factory design. The next owner can modify the
car if he wants, but any car I own will be the same as the factory designed
it.
My goal is to recreate, as closely as I
can, the exact experience of owning one of these cars when they were new.
I even go so far as to reproduce the inspection daubs of paint on the various
adjustments and the crayon markings on the engines, and the paint overspray on
some of the components (fuel pump, accelerator linkage, spark plug wire guides
etc). I know I’m a nut, but that’s the way I like to see them
done, and I practice what I preach.
As for the difference between 67 and 68
heads, I own both years (2 cars each), and I notice a much quicker throttle
response with the 67s than I do the 68s, with engines in equal (very good)
condition – I ascribe that to the smaller intake valves and passages in
the 67 heads, as compared to the 68s. I know the 68’s have better
high speed performance, but I don’t drive 100+ mph very often. I
drive at normal speeds most of the time, and I like the quick
“bite” of the car when you first tip into the throttle.
I’d guess going to the even larger intake valve heads would make a big
improvement at the drag races, but that’s not my bag.
So, thanks again, but no thanks.
Subject: Re: IML: Dick
B's valves
>>>For about $1300
you can get brand new Edelbrock aluminium heads with all new valves, springs,
hardened seats, bronze guides, etc. which because they are
aluminium will happily run 10:1 compression on pump gas. They also weigh
about 50 lbs less that the iron heads. The 452 casting # heads are the 1976-78
B and RB (400 and 440) heads with good flow and hardened seats.
>>>>I know what a
lot of urban myths say but that
should be laid to rest with evaluations done by
MOPAR performance magazines on big block
heads. If you want hardened valve seats get a
set of 400 heads from the wrecker. Problem
solved. And they breath very well, better than
the old heads.They are open chamber so your
compression ratio may go down depending on your
engine but there are ways of fixing that.
<<<<<<<<<<
Imperial-less in afghanistan
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
|
Back to the Home of the Forward Look Network