Re: IML: 1957 Imperial turning lens Option
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: IML: 1957 Imperial turning lens Option



This is true for both '55 & '56.

Paul W.


-----Original Message-----
From: Jan Harmonson <jharmonson@xxxxxxxxxxxxxxxx>
To: mailing-list@xxxxxxxxxxxxxxxx
Sent: Wed, 17 Oct 2007 10:52 am
Subject: Re: IML: 1957 Imperial turning lens Option



Hi

 

My 1955 sedan has yellow lenses in the tail lights that face forward allowing oncoming drivers to see the turn signals and also the brake lights. They are also visible in the rear view mirror so the driver knows what's working.

 

Jan in Ojai, CA

1955 Sedan


----- Original Message -----

From: pnkmoore@xxxxxxxxxxxxx

To: mailing-list@xxxxxxxxxxxxxxxx

Sent: Wednesday, October 17, 2007 11:06 AM

Subject: IML: 1957 Imperial turning lens Option




There is a '57 on Ebay with fender-top turning lights.  These are the lights that flash back at the driver to show the signal.  They are very common to later Chrysler products, but I don't think I've ever seen them on a car this old.  I wonder if they're after-market? Check it out at:

140168136637

 

Patrick

'58 Southampton (without fender turning lights)

 


----- Original Message -----

From: Gary Wilson

To: mailing-list@xxxxxxxxxxxxxxxx

Sent: Wednesday, October 17, 2007 10:55 AM

Subject: Re: IML: 1956 Imperial WHEEL CYLINDERS




You got it right. I would put some sil glide on the rubbers and in the cyclinders.  Make installation much easy and just works better.  Or at least some brake fluid in the cyclinder and on the rubber cups. 


----- Original Message -----

From: Timothy Hulse

To: mailing-list@xxxxxxxxxxxxxxxx

Sent: Tuesday, October 16, 2007 10:06 PM

Subject: IML: 1956 Imperial WHEEL CYLINDERS




Im sorry everyone but I was tired and stupid last night when I asked the question about cylinders. What I was talking about were the Wheel Cylinder kits. The kits come pakaged so you can rebuild the front or the rears. The original wheel cylinders have an aluminum PISTON with the rubber boot made on the piston and then one spring. My question is what goes back in the cylinder from the generic rebuild kit? I would assume we have to use the original PISTON. The only thing I can see how to make them work is as follows.

 

Slide the spring in the cylinder.

Slide the rubber cup in the cylinder.

Slide the original PISTON with the Original rubber boot made on the piston in the cylinder.

Then of course the boot and link.

 

Please correct me if this is wrong. The cylinders have been honed and ready.

 

Thanks for any help.

Tim Hulse

Bakersfield Ca

1956 Imperial






No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.5.488 / Virus Database: 269.14.13/1075 - Release Date: 10/17/2007 9:38 AM



________________________________________________________________________
Email and AIM finally together. You've gotta check out free AOL Mail! - http://mail.aol.com

-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to iml.webmonster@xxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm



Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.