The Forward Look Network | ||
| ||
56 Dodge Front Windscreen Trim Clip wanted Jump to page : 1 Now viewing page 1 [50 messages per page] | View previous thread :: View next thread |
Forward Look Swap Meet -> Wanted - All Wanted Ads | Message format |
Steve1956 |
| ||
Regular Posts: 81 | Looking for one or two trim clips that help hold the wide stainless trim in place on the front windscreen of a 1956 Dodge. I have looked at a number of vendors, can't seem to find anything close. Not sure if they are used on Plymouth? A small item only, hoping someone can help? If not I will have to try and make one, but I would prefer the genuine article...it would be a lot better than anything I can make. Thanks , Steve (IMG_3322.JPG) (56 Dodge Front Wscreen trim clip.jpg) Attachments ---------------- IMG_3322.JPG (39KB - 111 downloads) 56 Dodge Front Wscreen trim clip.jpg (39KB - 113 downloads) | ||
56D500boy |
| ||
Expert 5K+ Posts: 9911 Location: Lower Mainland BC | Steve1956 - 2021-01-16 2:02 PM Looking for one or two trim clips that help hold the wide stainless trim in place on the front windscreen of a 1956 Dodge. I have looked at a number of vendors, can't seem to find anything close. Not sure if they are used on Plymouth? A small item only, hoping someone can help? If not I will have to try and make one, but I would prefer the genuine article...it would be a lot better than anything I can make. Thanks , Steve Steve: If you can find the part number in the 55-58 Mopar Parts catalog, I can ask my local NOS parts guy if he has any. Barring that, they don't look very difficult to make, even out of say 16 gauge Stainless Steel. | ||
Steve1956 |
| ||
Regular Posts: 81 | My best guess from my parts manual is that the part is # 1646929 "Clip - hold down", "D62, D63 ", 2 required found in Parts Group 23R Windshield Outside Finish Mouldings Edited by Steve1956 2021-01-16 7:49 PM | ||
56D500boy |
| ||
Expert 5K+ Posts: 9911 Location: Lower Mainland BC | Steve1956 - 2021-01-16 4:48 PM My best guess from my parts manual is that the part is # 1646929 "Clip - hold down", "D62, D63 ", 2 required found in Parts Group 23R Windshield Outside Finish Mouldings I can find that PN in the 1956 Chryco parts hardcopy catalog but it does NOT show up in the 55-58 Mopar parts pdf and it does NOT show up at either Len Dawson's or Grease Monkey (formerly Collectors). So I think you might be out of luck for a new one. Try John F. at Big M. Sorry, Steve. | ||
22mafeja |
| ||
Elite Veteran Posts: 655 Location: Finland | I found a couple of 56 dodge clips but they look small to me...it is a mm measure. If they are the right ones it will be 5 usd including shipping....you will probably get them in the spring... Edited by 22mafeja 2021-01-17 1:30 PM (IMG_20210117_104923_BURST001_COVER_resized_20210117_105027127xxxx.jpg) Attachments ---------------- IMG_20210117_104923_BURST001_COVER_resized_20210117_105027127xxxx.jpg (37KB - 107 downloads) | ||
Steve1956 |
| ||
Regular Posts: 81 | Thankyou Thankyou. Yes they are the correct ones. I have sent you a PM. Edited by Steve1956 2021-01-17 4:06 PM | ||
Jump to page : 1 Now viewing page 1 [50 messages per page] |
Search this forum Printer friendly version E-mail a link to this thread |
(Delete all cookies set by this site) | |