Re: Getting stuff readcy

On Wed, Jul 17, 2013 at 11:39 PM, Steve Mick <micher@xxxxxxxxxxxxxxx> wrote:

Driveshaft looks great. Where did you get the work done? Did they have all the parts on hand? Which series U joints did you use? Could you give me the breakdown on costs? I have the yoke I want to use, but want to compare it to what they have - for strength. I have a D shaft that will get my car to move, but it is too short for acceleration tests 8-) .......................MO

{Steve Mick}
http://stevemick1964dodge.shutterfly.com/pictures/5

----- Original Message -----

From: Richard Kinsley

To: 1962to1965mopars@xxxxxxxxxxxxxxxx

Sent: Wednesday, July 17, 2013 4:45 PM

Subject: Getting stuff readcy

I got my new driveshaft back today. It's a 3" unit while my old one was 2&3/4". The trans is mounted and adjusted except for the kickdown. That will have to wait until the engine is installed and the carb is on. Yes it will be a carb for the time being until I raise the extra coins for the EFI.

Now I can get going on the engine ass'y. There is a parade July 17th that I would like to make if possible. We'll see how that goes!?

Rich Kinsley '64 Dodge Polara 4dr LeRoar 324 poly w/goodies

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/groups/opt_out.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/groups/opt_out.

--
Rich Kinsley '64 Dodge Polara 4dr 318poly w/goodies