RE: adjusting axle bearing

they are sealed single unit but look like rollers . ma mopar performance says enough ...

> Date: Sun, 13 Jan 2013 11:24:04 -0800
> Subject: Re: adjusting axle bearing
> From: micher@xxxxxxxxxxxxxxx
> To: 1962to1965mopars@xxxxxxxxxxxxxxxx
>
> Sven. are the bearings in that kit the ball bearing or timpkin
> bearing?................MO
>
> On Jan 13, 1:21 pm, MO <mic...@xxxxxxxxxxxxxxx> wrote:
> > Thanks Mike, I looked on line and Mancini appears to offer a kit that
> > includes differential parts that I don;t need. I will give them a
> > phone call if I can't get the kit from local parts
> > store. ................MO
> >
> > On Jan 13, 7:48 am, Michael LeFevre <493m...@xxxxxxxxx> wrote:
> >
> >
> >
> > > Steve,
> > > Always check with Mancini. They are very good with the drivetrain parts.
> > > Mike LeFevre
> >
> > > On Sat, Jan 12, 2013 at 7:18 PM, MO <mic...@xxxxxxxxxxxxxxx> wrote:
> > > > Thanks Sven and Eric. that tells me about everything I need to know.
> >
> > > > Is there bearing, seals, and gasket kits available all together? I
> > > > searched some, but could only find individual
> > > > componets..............MO
> >
> > > > On Jan 12, 1:37 pm, MO <mic...@xxxxxxxxxxxxxxx> wrote:
> > > > > I have a 64 Dodge 440 and the service manual for it( taper axle)
> > > > > However I am putting in a Flange axle 1965 rear houseing. Could
> > > > > someone send me or post here, a parts breakdown pic and how to adjust
> > > > > axle end play ? I know it is done on the right side, but not sure how
> > > > > it looks and how it works. And, is the wheel bearings a tight fit in
> > > > > the houseing requiring a puller? As always, I appreciate the
> > > > > input.................MO
> >
> > > > --
> > > > --
> > > > --
> > > > Please address private email -- email of interest to only one person --
> > > > directly to that person. That is, email your parts/car transactions and
> > > > negotiations, as well as other personal messages, only to the intended
> > > > recipient. Do not just press "reply" and send your email to everyone using
> > > > the general '62-'65 Clubhouse public email address. This practice will
> > > > protect your privacy, reduce the total volume of mail and fine-tune the
> > > > content signal to Mopar topic. Thanks!
> >
> > > > 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> > > >http://www.1962to1965mopar.ornocar.org/mletiq.htmland
> > > >http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> > > > --
> > > > You received this message because you are subscribed to the Google Groups
> > > > "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> > > >http://groups.google.com/group/1962to1965mopars?hl=en.-Hide quoted text -
> >
> > > - Show quoted text -- Hide quoted text -
> >
> > - Show quoted text -
>
> --
> --
> --
> Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> --
> You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> http://groups.google.com/group/1962to1965mopars?hl=en.
>
>
>