Re: How to make some A-B-Normal pushrods
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: How to make some A-B-Normal pushrods



Glad you got i fixed
Don't break it again.

The large downloads are killing me, again. :-(

.
On 8/20/2012 9:00 PM, Richard Kinsley wrote:
Well just in case anyone is interested I can tell/show you how to make some really unique push rods.  First you go in a parade with your old hot rod.  Then you rev up the engine to please the crowd.  Then you let 'er rip up to close to 8K to impress the cute girls.  Then you watch as the fan belts shoot out from under the hood and the engine begins to heat up.  Then you pull over, retrieve the belts, re-install the belts and go on your way.

However you notice the vacuum gauge is now oscillating.  Hmm too lean?  When you get home you pull the plugs and find that #6 is foouled and the rest are fine.  So you do a compression test and #6 has 125lbs with or without oil while the rest have about 170lbs.  So you pull the valve cover and WALLA #6 cylinder has blown the pushrods :-(  So then you pull out, with great difficulty, the pushrods and find the lifters are in place BUT the tip of the intake pushrod is not on the pushrod.  So you get an idea to insert a magnet and see if you can fish it out.  And being the lucky son-of-a-gun that I am I actually retrieve it all in one piece!!!!!!!!!!!   WooHoo.  Install some spare pushrods.  Re-adjust ALL the valves and I'll be darned it's running even better than it was before:-)

Yes I am truly one lucky guy.  Perhaps the moral of the story is not to rev it that high even if it'll go there.

Rich Kinsley '64 Dodghe Polara LeRoar 4dr 324 poly w/goodies
--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
 
 
 

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
 
 
 


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.