RE: Changing upper ball joints
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Changing upper ball joints



Thanks Gary.
 
I already disassembled the front end, but I notice I did not follow step 3 correctly, hope I did not damage the lower ball joint but I am installing new ones anyway....
 
I was checking to see if anyone had changed any upper ball joints lately because I was informed by an old mechanic that those upper ball joints are a bear to remove. Earlier today I ordered an Mopar ball joint impact socket that I can use with my high power impact wrench, so we will see. Maybe they will come right out, or not. I will let you know how it goes.
 
-Ben
 
> From: 62to65mopar@xxxxxxxxxxx
> To: 1962to1965mopars@xxxxxxxxxxxxxxxx
> Subject: Changing upper ball joints
> Date: Sat, 20 Aug 2011 20:28:11 +0000
>
> Returning member Ben asked about this procedure. I was looking into this topic myself. Below is one method, excerpted from this source:
> http://wiki.answers.com/Q/How_do_you_Replace_the_ball_joints_on_an_old_mopar_ABE_body.
> It is talking about both upper and lower ball joints.
>
> Any corrections / other methods welcome!
>
> ===
> Back off the torsion bar adjusters....Make sure they're loose in their mounting slots so that no tension remains on the front end components.
>
> 1. Remove brake drum, caliper, and/or rotor. On a drum brake car, you don't need to worry about removing the brake line from the cylinder, or the cylinder from the backing plate. They will all come off as an assembly in the next step.
> 2. Remove the two large bolts from the lower ball joint. Note how these bolts sandwich brake components together so you can reassemble them in the correct order later.
> 3. Remove the lower ball joint's cotter pin from the tapered shaft, and back the nut off 2-3 turns. Do not fully remove the nut at this point. Place the proper puller over the spindle and press the tapered shaft out. Make sure to get one of the small, thick-armed puller designed especially for this. Using the typical hinged "gear puller" will cause you a lot of grief. Believe me; it's worth it to get the correct puller! Obviously, you'll need to remove the nut before you can go any further. I leave the nut on during this operation to avoid damaging the threads while using the puller. This will completely separate the lower ball joint from the car.
> 4. Pull the upper tapered shaft the same as you did with the lower ball joint.
> 5. Next is the special socket that fits over the upper ball joint. The ball joints have very shallow threads formed into their sides that pull them into the control arms, so they're unscrewed just like a huge, short bolt....
> ===
>
> Thanks,
> Gary H.
>
> --
> --
> Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> --
> You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> http://groups.google.com/group/1962to1965mopars?hl=en.

--
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.