Re: ignition and alternator wireing HELP!

["MO ( Steve Mick)" <micher@xxxxxxxxxxxxxxx>]

OK I took my own advice and did a google search. I think I have found the 
answer to my voltage reulator issue.  I  will try that out tomorrow 
too.......................MO

{Steve Mick}
http://stevemick1964dodge.shutterfly.com/pictures/5
----- Original Message ----- 
From: "MO ( Steve Mick)" <micher@xxxxxxxxxxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Tuesday, February 15, 2011 7:15 PM
Subject: Re: ignition and alternator wireing HELP!


> Thanks Tom , that is a very good wireing diagram, and all who gave me 
> input. I think the ignition problem is solved. Thre clue was -the brown 
> wire to the ballast resister.   I had checked that  wire. It had a splice 
> terminal on the end and no other wire to the other end of the splice. No 
> power from it even with the ignition switch on. I thought maybe it only 
> had power when the starter was cranking, so I hooked up a remote starter 
> button--No Go. Then when I found out the ballast needed a brown wire to it 
> for sure. So--I wondered if the starter needed to be cranking with the 
> ignition switch. The wifey ran the ignition switch while I tested the 
> brown wire, and BINGO. --full 12 volts to it with the starter cranking. 
> Ran out of time so tomorrow I will hook everything up and test again.
>
> Now to figger out the alternator and electronc regulator  issue.  I need a 
> simple wireing diagram like the one Tom posted, but for a electronic 
> regulator Any more input??Thanks .....................MO
>
> {Steve Mick}
> http://stevemick1964dodge.shutterfly.com/pictures/5
> ----- Original Message ----- 
> From: "Tom Watters" <tomwatters@xxxxxxxxxxx>
> To: <1962to1965mopars@xxxxxxxxxx>
> Cc: "MO ( Steve Mick)" <micher@xxxxxxxxxxxxxxx>
> Sent: Tuesday, February 15, 2011 12:34 PM
> Subject: Re: ignition and alternator wireing HELP!
>
>
> > Here's a link to the '65 B-Body wiring diagram.
> >
> > http://members.cox.net/metalchewy/Tw1020.jpg
> >
> > Connection to the starter relay would be thru the bulkhead and ignition 
> > switch.
> >
> > On 02/14/2011 11:04 PM, MO ( Steve Mick) wrote:
> > > This is on a 64 Fury 383 with cobbled up under hood wireing.
> > >
> > > issue #1-points distributor-wireing to the input side of ballast 
> > > resister. We know that when engaging the starter, voltage to all systems 
> > > is reduced. However there is a wire that maintains full voltage even 
> > > when the starter is cranking . That wire needs to be on the input side 
> > > of the ballast resister, so that it gets full voltage even when 
> > > cranking.  Where does that wire come from? Through the bulkhead or from 
> > > the starter relay or???
> > >
> > > issue #2 fairly thin , chrome rectangular voltage regulator mounted on 
> > > the firewall with a 2 prong plug on the front side . No other wires. 
> > > Take off the plug and test both prongs on the regulator with the ign. 
> > > switch on , should one of the prongs have power to it?  One prong goes 
> > > to a post on the alternator and the other prong goes to another post on 
> > > the alternator. No other wires to the alternator Shop manual wireing 
> > > diagram is too much for me to make out.
> > >
> > > I THINK--the full time 12 volt wire to the ballast resister comes from 
> > > the starter relay, but I cannot  find a ignition switched  connection 
> > > that does not reduce voltage when cranking. HELP!!!......Thanks for any 
> > > input...................MO
> > > .... .
> > > {Steve Mick}
> > > http://stevemick1964dodge.shutterfly.com/pictures/5
> > >
> > > ----
> > > Please address private mail -- mail of interest to only one person -- 
> > > directly to that person.  I.e., send parts/car transactions and 
> > > negotiations as well as other personal messages only to the intended 
> > > recipient, not to the Clubhouse public address. This practice will 
> > > protect your privacy, reduce the total volume of mail and fine tune the 
> > > content signal to Mopar topic.  Thanks!
> > >
> > > 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> > > http://www.1962to1965mopar.ornocar.org/mletiq.html and 
> > > http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
>
>
> ----
> Please address private mail -- mail of interest to only one person --  
> directly to that person.  I.e., send parts/car transactions and 
> negotiations as well as other personal messages only to the intended 
> recipient, not to the Clubhouse public address. This practice will protect 
> your privacy, reduce the total volume of mail and fine tune the content 
> signal to Mopar topic.  Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and 


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.