Re: 360 swap
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: 360 swap



You also have to be careful that you are not dealing with a lock up conveter.   
That was in some  Cardobas.  It has a different main shaft that enters into the 
converter. 




----- Original Message ----
From: Mike and Linda <miclinmopar@xxxxxxxxxxxxx>
To: 1962to1965mopars@xxxxxxxxxx
Sent: Wed, September 1, 2010 7:06:25 PM
Subject: Re: 360 swap


You can use your stock converter and the stock 904 transmission but there 
are 2 things to check;

1)  check the snout of the TC.  If its the small 65/earlier type, you'll 
need and adapter ring (bushing) for the larger size crank bore.
2)  you can also use that neutral TC IF you get the TCI special "balanced" 
360 flexplate for a 904 trans.  They also have a balanced flexplate for 
727.

Mike


----- Original Message ----- 
From: "Herb" <zephyr9900@xxxxxxxxxxx>
To: "1962 to 1965 Mopars" <1962to1965mopars@xxxxxxxxxx>
Sent: Wednesday, September 01, 2010 9:03 PM
Subject: Re: 360 swap




Converter will be a problem.  The converter for the 360 balance has a larger
input shaft than the present converter.  The converter will fit but the car
will not move!  That said it is a simple fix, just replace the old pump and
input shaft with a newer one from a 727.




              
Herb

1956 Plymouth Belvedere 361 4-Sale
1959 Coronet 326 Poly
1961 Belvedere Custom Suburban 318 Poly
1962 Dodge Dart 225 Slant Six  4-Sale
1963 Fury 2D/HT 6.1L
1963 Sport Fury Convertible 361
1970 Chrysler 300 Hurst 440
1999 Durango SLT 5.9L
2008 SRT-8 Magnum 6.1L
St. Louis, MO.

http://1962to1965mopar.ornocar.com/mmo42009.html




-------Original Message-------

From: Joey
Date: 9/1/2010 7:56:43 PM
To: 1962to1965mopars@xxxxxxxxxx
Subject: Re: 360 swap

the engine should bolt up to your 727, might want to check on converter
weights though, later 360's I think are balanced differently.

Joey
----- Original Message -----
From: "Don" <mopar4me@xxxxxxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Wednesday, September 01, 2010 7:33 PM
Subject: Re: 360 swap


>
>  You'll definitely have to swap the oil pan (truck/van is rear sump) and
> use the oil pickup for the center sump.  You'll also need a car 360 oil
> pan - 273/318/340 pans won't fit the 360.
> Don
>
> On 9/1/2010 5:01 PM, Dooner Funderburk wrote:
>>
>> My poly 318 in my 64 Belvedere isn't a good running dependable engine
>> right now (many different reasons), and I have an opportunity to swap in
>> a running 360 from a 80s model Dodge van. It has been slightly refreshed
>> and best of all, it is free. It will be a temp engine swap till I can
>> save up money to restore. I want to enjoy driving the car some.
>>
>> Will this swap work? What heads up can you give me, on things that will
>> not work (oil pan, exhaust manifolds, fit my 727, etc.)?
>>
>> Thanks guys
>>
>> Dooner
>>
>> ----
>> Please address private mail -- mail of interest to only one person --
>> directly to that person.  I.e., send parts/car transactions and
>> negotiations as well as other personal messages only to the intended
>> recipient, not to the Clubhouse public address. This practice will
>> protect your privacy, reduce the total volume of mail and fine tune the
>> content signal to Mopar topic.  Thanks!
>>
>> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
>> http://www.1962to1965mopar.ornocar.org/mletiq.html and
>> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
>>
>>
>>
>
>
> ----
> Please address private mail -- mail of interest to only one person --
> directly to that person.  I.e., send parts/car transactions and
> negotiations as well as other personal messages only to the intended
> recipient, not to the Clubhouse public address. This practice will protect
> your privacy, reduce the total volume of mail and fine tune the content
> signal to Mopar topic.  Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and
>
>


----
Please address private mail -- mail of interest to only one person --
directly to that person.  I.e., send parts/car transactions and negotiations
as well as other personal messages only to the intended recipient, not to
the Clubhouse public address. This practice will protect your privacy,
reduce the total volume of mail and fine tune the content signal to Mopar
topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www
1962to1965mopar.ornocar.com/general_disclaimer.html.



[Non-text portions of this message have been removed]


----
Please address private mail -- mail of interest to only one person --  
directly to that person.  I.e., send parts/car transactions and negotiations 
as well as other personal messages only to the intended recipient, not to 
the Clubhouse public address. This practice will protect your privacy, 
reduce the total volume of mail and fine tune the content signal to Mopar 
topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and 
http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.


----
Please address private mail -- mail of interest to only one person -- directly 
to that person.  I.e., send parts/car transactions and negotiations as well as 
other personal messages only to the intended recipient, not to the Clubhouse 
public address. This practice will protect your privacy, reduce the total volume 
of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and 
http://www.1962to1-----------------------------------






Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.