RE: Winter project thoughts
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Winter project thoughts



I would like to see improvement on the 60' times.
Rich Kinsley '64 Dodge Polara 4dr 318poly w/goodies
==================================================================
Herb wrote:
> 
> 
> You would loose low end torque by removing the wall and may only 
> slightly
> gain on the top end.  I guess you have to decide were you are lacking, 
> low
> end, off the line or high end, through the finish line.
> 
>           
>  Herb 
>  
> 1956 Plymouth Belvedere 361
> 1959 Coronet 326 Poly
> 1963 Fury 2D/HT 6.1
> 1963 Sport Fury Convertible 361
> 1970 Challenger RT 440 - 4 Sale
> 1999 Durango SLT 5.9
> 2008 SRT-8 Magnum 6.1
> St. Louis, MO.
>  
> http://1962to1965mopar.ornocar.com/mmo42009.html
>   
>  
>  
>  
> -------Original Message-------
>  
> From: Rich Kinsley
> Date: 10/16/09 23:19:26
> To: 1962to1965mopars@xxxxxxxxxx
> Subject: Winter project thoughts
>  
>  
>  
> Rich Kinsley '64 Dodge Polara 4dr 318poly w/goodies
>  
> I remember someone mentioning that they built up the intake manifold
> under the carb venturi with JB Weld that tapered off towards the outside
> to help force the gases towards the intake valves. My Weiand WPD4D has a
> seperating wall between each side with only small notches as a balancer
> right under the carbs. I have been thinking of removing most of the wall
> under the carbs and perhaps building a small sheetmetal ramp over the
> center wall area. Perhaps I could drill and tap for screws to fasten it
> down. I'd kinda like to get the manifold powdercoated so while it's out
> I could play with it a bit. Maybe JB Weld would be a better option but
> I'm wondering what would happen if it broke up and headed into the
> engine?  Anybody got any thoughts of what impact this mod might have?
>  
>  
> ----
> Please address private mail -- mail of interest to only one person --
> directly to that person.  I.e., send parts/car transactions and 
> negotiations
> as well as other personal messages only to the intended recipient, not 
> to
> the Clubhouse public address. This practice will protect your privacy,
> reduce the total volume of mail and fine tune the content signal to 
> Mopar
> topic.  Thanks!
>  
> '62 to '65 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html.
>  
> [Non-text portions of this message have been removed]
> 



Rich Kinsley '64 Dodge Polara 4dr 318poly w/goodies


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 

This email was sent to: arc.6265@xxxxxxxxxxxxxx

u/?bUrDWg.bSONJP.YXJjLjYy



?p=TEXFOOTER




Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.