Re: Flywheel
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Flywheel




You didn't specify which year 360, so I didn't want to presume. Assuming you are using a bell from the same year, 130t should be correct.

Wakeman

----- Original Message ----- From: "Knud-Erik Holm" <kebh@xxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Tuesday, March 17, 2009 1:58 AM
Subject: SV: Flywheel



Thank you for the reply,

I went to purchase the flywheel, and things did not go as planned, the guy
has a big ship container filled with new and used parts for 60 to 70 mopar,
everything Is mixed together. After 2 hours we had to give up. I will return
this Saturday and we will clear it all out and sort it right. Some of it
will have to be dumped to scrap.

But I am looking forward to Saturday.

About the flywheel, I thought that it was only 130 tooth that will fit on a
360 2 bbl from 1974

Thanks,

Knud-erik Holm

-----Oprindelig meddelelse-----
Fra: Wakeman Massie [mailto:wakey@xxxxxxxxxxx]
Sendt: 15. marts 2009 22:53
Til: 1962to1965mopars@xxxxxxxxxx
Emne: Re: Flywheel


Cast iron is fine for any normal/mild performance application. The flywheel
would be fine IF the flywheel is the correct tooth count for your
bellhousing...130 or 143.

But you still need to properly address your balancing situation.  Balancing
the crank/fly/clutch together isn't going to do it.

You need to first balance the engine's rotating assembly - pistons, rods,
bearings, crank, balancer, rings, etc.  Have you sourced an internal balance

balancer yet?  Then you can balance the flywheel with all this if you like
or zero-balance the flywheel on its own.  Which it already should be if it
is from a 318...

Unless this is a high-performance application, and/or you are bent on
internally balancing your 360 anyway, I think you are better off leaving the

engine balance alone, and buying the correct flywheel for your application,
i.e. an externally balanced 360 flywheel.  If you're willing to pay $400 you

could easily find one stateside and have it shipped.

Confused yet?

Wakeman

----- Original Message ----- From: "Knud-Erik Holm" <kebh@xxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Sunday, March 15, 2009 9:54 AM
Subject: Flywheel



Hi,

I have recieved an offer for a 318 flywheel I am suppose to pick up tomorrow
after work. My question is this; he says it is cast iron, is it a good
choice for my 360? I am aware of internal and external balance, however I
have planned to have the crankshaft and the flywheel+clutch balanced at a
shop where they balance Porsche engines. The price for the flywheel
including balancing will be 400 us $

Is this the right choice?

Thanks, Knud Holm ´62 fury


----
Please address private mail -- mail of interest to only one person --
directly to that person.  I.e., send parts/car transactions and negotiations

as well as other personal messages only to the intended recipient, not to
the Clubhouse public address. This practice will protect your privacy,
reduce the total volume of mail and fine tune the content signal to Mopar
topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.


----
Please address private mail -- mail of interest to only one person --
directly to that person.  I.e., send parts/car transactions and negotiations
as well as other personal messages only to the intended recipient, not to
the Clubhouse public address. This practice will protect your privacy,
reduce the total volume of mail and fine tune the content signal to Mopar
topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.


----
Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.
This email was sent to: arc.6265@xxxxxxxxxxxxxx

u/?bUrDWg.bSONJP.YXJjLjYy



?p=TEXFOOTER











Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.