I've been out of town, otherwise I'd have chimed in sooner.
I have an 833 OD in my '65 Polara (C-body, but uses the same trans as
B-bodies).
I used the truck/van version of the OD.
Fourth gear is something like 0.74:1.
I solved the bearing retainer problem pretty easily.
I removed the retainer from the trans and chucked it up on a brake
lathe. I
then turned down the outside diameter until it fit my bellhousing.
There's
plenty of meat on the retainer so have no fear (but at least look at
what
you're doing, because you might have a smaller bellhousing than I).
I pieced together the shifter linkage and had to make some adjustments
to my
handle because I had the wrong shifter mounting pad, but it works great
now.
I've had it behind my 413 for three years now with no problems. It has
seen
plenty of highway cruising in overdrive in that time. It has also held
up to
being driven hard in a 5000 lb car, but I don't dare powershift it.
I'm running a 3.23 in the back with 255/60R15 tires. First gear is
pretty
low, so you'll probably prefer to take off in 2nd with your 3.91.
Also, the gap between 1st and 2nd is pretty wide, so the shifting isn't
as
fast as you'd like it to be since you have to wait for the input to spin
down or double clutch. Shifting 2-3-4, or even 2-4 can be done pretty
fast.
Second gear is my favorite because my engine raps out at about 70mph in
second (cast pistons, don't turn it past 5000). If you're spinning to
6k,
then first gear might be a little more useful and second will be a
blast.
Dave Casey
----- Original Message -----
From: <ledman_70@xxxxxxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Wednesday, July 18, 2007 7:20 AM
Subject: RE: A833 OD questions
>
> Thanks Doug, I was hungry! I picked up the tranny and had the car on
> the
> rack to compare...the tailhouses are the same length, but the trans
> mount is in a different location, but I can fab that ok, I think. The
> shifter mount pad seems to be in the same location on both. The OD has
> a
> bracket to raise the shifter up higher, but I can work around that,
> too.
> The other issue you pointed out is the size of the bearing retainer.
> The
> OD retainer is 5.25", but I don't know the size of the standard
> 833..anybody have that measurement? I'm not ready to pull the trans to
> measure it.
> Doug Ahern wrote:
>>
>> On 30 07/13/07, ledman_70@xxxxxxxxxxx wrote:
>> > Sounds like more trouble than it's worth...then again, almost 3k rpm
>> > at
>> > 60 sure rattles your teeth in a 40+ year old car. Guess I'll keep
>> > looking. Thanks for the info Doug....can I have my fruit cup now?
>>
>> its un-nerving for us now because we are accustomed to 70mph @
>> 2400rpm,
>> but in the 1960s, speed limits were just as high and people drove up
>> and down interstates @ 65-75mph with 3.23:1 and 2.93:1 gears and short
>> little tires on 14" wheels.,, so 3500rpm @ 70mph was normal then.
>> the car nor the engine actually mind it, but we think its too high....
>>
>> sure.., it friday.. you eat your fruit cup now.
>>
>
>
>
> Jeff Adams
> 64 Polara
>
>
> ----
> Please address private mail -- mail of interest to only one person --
> directly to that person. I.e., send parts/car transactions and
> negotiations as well as other personal messages only to the intended
> recipient, not to the Clubhouse public address. This practice will
> protect
> your privacy, reduce the total volume of mail and fine tune the content
> signal to Mopar topic. Thanks!
>
> '62 to '65 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html.
>
>
>
Back to the Home of the Forward Look Network