RE: sure grips

[ntolerance <ntolerance@xxxxxxxxxxx>]

[AD removed for archives]
-------------------------------------------------------------------
Click here and get your free* stock car racing gift.
caac8uaa/PermissionData
-------------------------------------------------------------------

The clutch type sure grips were modeled after the Dana 60 powerlock 
unit. I believe Dana may have even built them for Chrysler. They even 
share a few parts between the two units.

The Cone type , or Auburn units are not as durable. Although you can 
shim and mill them to get them to work again, they are a grenade waiting 
to happen after such work. (seen it done, the track guys get all mad 
when you slick down the staging lanes with gear oil) Certain earlier GM 
"posis" used a similiar system. Even though its not as strong, its 
better than GM's Gov-loc (govenor lock, figure that one out.)

Still I think the question was whats an E body 3.91 Sg rear worth? 
Asuming it is a 489 case and its an E body axle ( e body is unique ) its 
still worth a decent chunk of change. I have seen some go for over $500 
complete. (or more depending on condition) This is a swap meet price, 
ePay may get more. People seem to think that having the 489 case is 
stronger and better for higher hp cars. This is somewhat true, but not 
if it has a cone type s/g unit. You can put a clutch type into any 489, 
742 or 741 case (there are limits to this, such as very early cases).

The "crush sleeve" ( found in a 489 case )in my opinion is a piece of 
crap set up. Shims are much better, although they can take longer to set 
up.

Doc.

tom hecht wrote:
> 
> you can also add shims, this pushes the cone
> closer . i beleive this can be done a couple times.
> this makes it cheaper to rebuild than the clutch type, 
>  
> there could be some argument
> about the lock-up quality from one to the other though.
>  
> tom
> 
> "Gary B." <wedge65@xxxxxxxxxxx> wrote:
> 
> That is correct, about it being the cone type, but they can be somewhat
> rebuilt by having about .080 milled off the back of the side gears and
> adding springs from a transmission clutch pack. It will make them work 
> for a
> while longer. Gary Bradshaw Ft. Worth, Texas
> 
> "I used to have a handle on life, but it
> broke"
> ----- Original Message ----- 
> From: 
> To: <1962to1965mopars@xxxxxxxxxx>
> Sent: Thursday, February 03, 2005 4:22 AM
> Subject: Re: sure grips
> 
> 
> [AD removed for archives]
> -------------------------------------------------------------------
> Get a FREE* Portable Satellite Radio - yours to keep! Click Here!
> caac8uyb7fOBRa/Portable Satellite Radio
> Promotion
> -------------------------------------------------------------------
> 
> 
> Is it true that if you can see the springs in the SG unit it is a cone 
> type
> and not rebuildable? Read that somewhere.....Joe
> 
> [Non-text portions of this message have been removed]
> 
> [AD removed for archives]
> -------------------------------------------------------------------
> Need a Laptop? Get a Sony Vaio Laptop Free!
> caac8usb7fOBRf/ProductTestPanel
> -------------------------------------------------------------------
> 
> ----
> Please address private mail -- mail of interest to only one person -- 
> directly to that person. I.e., send parts/car transactions and 
> negotiations
> as well as other personal messages only to the intended recipient, not 
> to
> the Clubhouse public address. This practice will protect your privacy,
> reduce the total volume of mail and fine tune the content signal to 
> Mopar
> topic. Thanks!
> 
> '62 to '65 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html.
> 
> [AD removed for archives]
> -------------------------------------------------------------------
> Get both the PlayStation2 and Game Cube for Free! Click here to 
> find out how.
> caac8utbOgXg2f/Consumer Research
> -------------------------------------------------------------------
> 
> ----
> Please address private mail -- mail of interest to only one person -- 
> directly to that person. I.e., send parts/car transactions and 
> negotiations as well as other personal messages only to the intended 
> recipient, not to the Clubhouse public address. This practice will 
> protect your privacy, reduce the total volume of mail and fine tune the 
> content signal to Mopar topic. Thanks!
> 
> '62 to '65 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html. 
> 
> 
> 
> 
> 
> __________________________________________________
> Do You Yahoo!?
> Tired of spam?  Yahoo! Mail has the best spam protection around 
> http://mail.yahoo.com 
> --
> [Non-text portions of this message have been removed]
> 

[AD removed for archives]
-------------------------------------------------------------------
Need a Laptop? Get a Sony Vaio Laptop Free!
caac8usf/ProductTestPanel
-------------------------------------------------------------------

----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 



http:///u/?.