Re: Holley Carb Help
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Holley Carb Help



[AD removed for archives]
-------------------------------------------------------------------
Save up to 67% on Omaha Steaks + Get 6 FREE Burgers and a 
FREE Cutlery Set + Cutting Board!
caaclxSb7yoMza/OmahaSteaks
-------------------------------------------------------------------

Hi Ken, I don't think your problem is the fuel pressure. Did you replace the
float bowls with end hung floats or center hung floats. Sometime the float
will drag on the rear metering plate (especially with center hung floats)and
hold open the needle and seat. If this is happening you can sometime just
bend the float mount a little and cure the problem. If the rear is flooding
and the stock carburetor still has the equalization tube between the bowls,
it can flood both ends of the carb. I build carburetors on the side and have
ran into that a number of times. Good luck with it.
Gary Bradshaw Ft Worth, Texas

----- Original Message ----- 
From: "Westerlund, Ken" <kwesterlund@xxxxxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Monday, June 21, 2004 11:02 AM
Subject: RE: Holley Carb Help


[AD removed for archives]
-------------------------------------------------------------------
Save up to 67% on Omaha Steaks + Get 6 FREE Burgers and a
FREE Cutlery Set + Cutting Board!
caaclxSb7fOBRa/OmahaSteaks
-------------------------------------------------------------------

Hi Rich,
You are probably right, but I don't understand why?  I have a new stock
fuel pump and rebuilt a factory carb.  The pressure wasn't too high when
the car first rolled off the line, why would it be too high now.  Do
aftermarket cams change the pressure?  I can throw a regulator on it,
but I don't want to just cover up some other problem.

Regards,
Ken

-----Original Message-----
From: Richard Kinsley [mailto:r.kinsley@xxxxxxxxxxxxxxxx]
Sent: Monday, June 21, 2004 10:33 AM
To: 1962to1965mopars@xxxxxxxxxx
Subject: Re: Holley Carb Help

I gotta believe the pressure must be too high. I always used a pressure
regulator to keep it in line.  Rich Kinsley '64 Polara 4 door
----- Original Message ----- 
From: "Westerlund, Ken" <kwesterlund@xxxxxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Monday, June 21, 2004 7:22 AM
Subject: Holley Carb Help


[AD removed for archives]
-------------------------------------------------------------------
Save up to 67% on Omaha Steaks + Get 6 FREE Burgers and a
FREE Cutlery Set + Cutting Board!
caaclxSb7KAyoa/OmahaSteaks
-------------------------------------------------------------------

Good news and bad news.
The good news is that we finally got our semi-rebuilt 440 started
(without its mufflers) for the first time.  After the 318 this sounds
great.

The bad news is that it only ran for about 15 seconds before fuel
started coming out of the bowl vents and I had to shut it down.  I
replaced the needle valves again and adjusted the float level down as
far as I could and again, the same thing happened.  I am using a stock
fuel pump and a Comp cam.  Are the Comp cams ground to stroke the fuel
pump more and increase fuel pressure?  My fuel pressure gage is being
pegged at 8 PSI.

The carb is the stock 1972 Holley that came with the 440 to which I
added adjustable float bowls.

Anything special I should be looking for?

Regards,
Ken

-----------------------------------------------------------
Buy Stocks and Index Funds for just $4 No Account or
Investment Minimums and No Inactivity Fees Automatically
invest weekly or monthly and build your future.
caaciqZb7fOBRf/Sharebuilder
-----------------------------------------------------------

----
Please address private mail -- mail of interest to only one person -- 
directly to that person.  I.e., send parts/car transactions and negotiations
as well as other personal messages only to the intended recipient, not to
the Clubhouse public address. This practice will protect your privacy,
reduce the total volume of mail and fine tune the content signal to Mopar
topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.

-----------------------------------------------------------
Sponsor a child today through Children International.  
Give a desperately poor child hope for a brighter future.
For only $18 a month you can make a difference!
caaciqSb7yoMzf/Children's Int'l
-----------------------------------------------------------

----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 



b7yoMz. 













Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.