Re: Help. I screwed up...
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Help. I screwed up...



Yank out the convertor drain plug, then make a pipe nipple reducer,
screw into convertor, attach hose , fill with fluid.


On 8/4/14, JimJablonski <groovinjim@xxxxxxx> wrote:
> Folks,
>
> I am getting very close to lighting up the stroker for the 1st time, and in
>
> prep for today came to the realization that I totally missed something - I
> didn't add the obligatory quart of tranny fluid to my brand new torque
> converter before installing it.  I talked to Sean at Dynamic this afternoon
>
> and let's just say he was lukewarm about anything other than pulling the
> trans and motor apart to yank the converter and give it a quart.
>
>
> Arghhh.  I am thinking there's another way.  Perhaps I yank the plugs, and
> with the fuel pump cut-off, crank the motor around to try to fill the
> converter before firing it up?  It would go something like this:
>
> 1) Add transmission fluid via dipstick and note fill location on dipstick
> 2) Remove plugs, disable ignition and fuel, then crank engine
> 3) Check location of fluid on dipstick and add as necessary
>
> What do you think - and can you think of ideas?  Or maybe I am just
> freaking out totally and should just fire it up and refill it as normal?
>
> Thank you,
>
> Jim
>
>
>
> --
> --
> --
> Please address private email -- email of interest to only one person --
> directly to that person. That is, email your parts/car transactions and
> negotiations, as well as other personal messages, only to the intended
> recipient. Do not just press "reply" and send your email to everyone using
> the general '62-'65 Clubhouse public email address. This practice will
> protect your privacy, reduce the total volume of mail and fine-tune the
> content signal to Mopar topic. Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and
> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> --
> You received this message because you are subscribed to the Google Groups
> "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> http://groups.google.com/group/1962to1965mopars?hl=en.
>
> ---
> You received this message because you are subscribed to the Google Groups
> "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
> For more options, visit https://groups.google.com/d/optout.
>

-- 
-- 
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

--- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/d/optout.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.