Re: Fw: 440 head question
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Fw: 440 head question



 Thanks folks for the replys, but I am still a little befuddled,  I
know the port that goes accross the intake, under the carb can be
blocked off with an intake gasket,  What I am concered with is the big
semi-circle holes arounf that port. in the head. looks like he** and a
trap for dirt and small parts.  Are those also covered by the
aftermarket intake gasket??

To Chick:  are you saying that instead of the stock type valley cover/
intakje gasket combo, that there is available a seperate valley cover
and seperate intake gaskets? . Thanks...........MO

On Jun 16, 11:53 am, "Stephen Andrachek" <s.andrac...@xxxxxxxxxxx>
wrote:
> My friend MO,
>
>  You are exactly right.  You can block off the heat passage from the heads
> to  the intake by using the correct valley cover.  You can get the valley
> cover
>  from Hughes Engineering (Google them up) and very good intake gaskets off
> of  them too with a bead of silicon built in around each port.
>
>  To take things a little farther, if you put an Edelbrock Air Gap intake on
>  your car with a low-restriction air cleaner you will pick up a noticable
>  amount of torque and HP.  But your engine is going to be a little
>  cold-blooded and will need a little warm up time that with the heat
>  passages blocked off.
>
>  Mancini's is also a great place to do business with.  Both companies are
> all
>  Mopar, all the time and will answer questions over the phone for you,
> unlike
>  Indy Cylinder Head which does not want to talk to their customers at all.
>  They consider that annoying and will refuse to answer your questions.
>
>  Hope this helps you in some way.
>
>  Stephen "Chick" Andrachek
>
>
>
>
>
> > ----- Original Message -----
> > From: "MO" <mic...@xxxxxxxxxxxxxxx>
> > To: "The 1962 to 1965 Mopar Mail List Clubhouse"
> > <1962to1965mopars@xxxxxxxxxxxxxxxx>
> > Sent: Thursday, June 16, 2011 2:21 AM
> > Subject: 440 head question
>
> >> This is for a 1978 head.Intake side -1/2 way between the intake
> >> ports.  where the heat crossover port is.  What does the semi-circle
> >> pocket in the casting intended to do. And what can be done to hide
> >> it?  I would be using valley cover with blocked off heat port.  Thanks
> >> for any help......................MO
>
> >> --
> >> You received this message because you are subscribed to the Google Groups
> >> "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> >> To post to this group, send email to 1962to1965mopars@xxxxxxxxxxxxxxxxx
> >> To unsubscribe from this group, send email to
> >> 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
> >> For more options, visit this group at
> >>http://groups.google.com/group/1962to1965mopars?hl=en.- Hide quoted text -
>
> - Show quoted text -

-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To post to this group, send email to 1962to1965mopars@xxxxxxxxxxxxxxxxx
To unsubscribe from this group, send email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit this group at http://groups.google.com/group/1962to1965mopars?hl=en.



Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.