Re: Master Cylinder rebuild
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Master Cylinder rebuild



Hay Ollie,  I been about as good as I get, but plenty of room for 
improvement.!! Getting things outdoors and the shop ready for winter. My 
painter is painting my dash and garnish moldings this week . Got my 
windshield area ( it is out) stripped, few little repairs, epoxy primered, 
and ready for urethane paint.  Got the floor pinholes repaired and POR 15. 
Thanksgiving weekend I should get my clutch-brake pedal assembly. You 
probably have seen my posts on the headliner- sailpanels.  With help from 
the good people here on the mail list, I have a pattern coming, and some 
panel board to look at. Been e- mailing with a person down in ARK. that has 
a parts car for sale, it has some pieces I need for the Chrysler and trying 
to wrangle a way to buy a couple cars I know I can make money on. Got my 50 
acres of corn and beans in the bin ( thanks to the neighbors) .Took the 
front fenders off the parts car----Thats about all my story--- and what you 
been doing?...........................MO
{Steve Mick}
http://stevemick.shutterfly.com/pictures#Part%202
----- Original Message ----- From: "Ollie" <satellite1965@xxxxxxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Thursday, November 18, 2010 3:02 PM
Subject: Re: Master Cylinder rebuild


I know he will take that single cyl in for a core, or at least my napa 
will.
How u been MO?
Ollie

----- Original Message ----- From: "MO ( Steve Mick)" <micher@xxxxxxxxxxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Thursday, November 18, 2010 2:56 PM
Subject: Re: Master Cylinder rebuild


Have you checked NAPA to se if you can get a rebuilt one with your 
exchange core?  In the long run, it could be the cheaper way to go and 
save a lot of #^$@*&^%$  I would guess there are some on e-bay from time 
to time...................MO
{Steve Mick}
http://stevemick.shutterfly.com/pictures#Part%202
----- Original Message ----- From: <62pluckedchicken@xxxxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Thursday, November 18, 2010 12:40 PM
Subject: RE: Master Cylinder rebuild


unfortunately I don't own an impact driver... I can try giving it a
couple of firm taps and see if that will free it up
Jimmy Peavy wrote:
  An impact  driver.
Put it in a vise on a block of wood, and use an impact driver, using a
big ball peen, or small 3lb sledge hammer.

Jimmy

On 11/18/2010 12:02 PM, 62pluckedchicken@xxxxxxxxx wrote:
> things have slowed down enough for me to get back to my Plucked > Chicken.
>
> I need to rebuild the MC, but can't get past the screw in the picture
>
> http://omaha.timelesstransport.com/wp-content/uploads/2010/11/ChryslerMC600.jpg
>
>
>
> two days of spraying it with PB Blaster and it won't budge... any > ideas
> on how to loosen this stubbon screw? heat? sledge hammer? ;)
>
>
> ----
> Please address private mail -- mail of interest to only one person -- > directly to that person. I.e., send parts/car transactions and
> negotiations as well as other personal messages only to the intended
> recipient, not to the Clubhouse public address. This practice will
> protect your privacy, reduce the total volume of mail and fine tune > the
> content signal to Mopar topic.  Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and
> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
>
>

----
Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.


----
Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and



----
Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.











Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.