Re: ECU and Engine Miss Diagnosis
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: ECU and Engine Miss Diagnosis



I am using the Accel coil. The coal is mounted horizontally, as a factoy coil is 
mounted, not with the connections pointed up. I'm sure I can rig up a vertical 
mounting on the inner fineder well without butchering up the panel. 


The ballast resistor is the four pronged unit that came with the electronic 
ignition conversion kit. Is this the 1.5 ohm resistor? Where do get these .25 
and .8 ohm resistors?

 
Akron Don Gallimore



----- Original Message ----
> From: Rich Kinsley <rlkinsley@xxxxxxxxx>
> To: 1962to1965mopars@xxxxxxxxxx
> Sent: Mon, October 4, 2010 10:52:15 AM
> Subject: RE: ECU and Engine Miss Diagnosis
> 
> 
> My coil positioning caused my coil to heat up and similar conditions 
> followed. My Accel must not be angled downward on level as it causes the 
> plates to be exposed and they arc and heat up the coil. Similarly I also 
> had issues with the wrong ballast resistor causing the ECU to have 
> problems with RPM's. I have mentioned this before. I use the .25 race 
> resistor when racing and a .8 resistor for the street. Some by-pass the 
> resistor for racing and I have done it in the past. It OK but if you run 
> at idle too long it can cause the coil to heat up and fail. My car would 
> flat die! The 1.5 resistor wouldn't allow RPM's over 5K, maybe less. 
> Just what I found.
> 
> Rich Kinsley '64 Dodge Polara 4dr 318poly  w/goodies
> =====================================================================
> Donald  Gallimore wrote:
> > 
> > Last trip to the drag strip, I developed a  miss around 2500 RPM=A0and 
> > up.=
> > =A0=A0Engine =0Aseemed like it  was loading up but carb looked good - 
> > floats=
> > =A0levels  are=A0right=0Aand we changed nothing on the carb.=A0 This may 
> >  hav=
> > e been developing for weeks and =0Afinally showed up late in 
> > eliminations.=
> > =0A=0AI'm going to replace the cap, rotor,  reluctor and pick up in the 
> > dist=
> > ributor =0Asince they are  relatively small cost items.=A0 Question is 
> > there=
> >  a way  to test the =0AECU? =0A=0A=0ALastly, any ideas on what (else) to 
> >   che=
> > ck to eliminate the miss?=0A=A0=0AAkron Don  Gallimore
> 
> 
> 
> Rich Kinsley '64 Dodge Polara 4dr 318poly  w/goodies
> 
> 
> ----
> Please address private mail -- mail of interest to  only one person -- directly 
>to that person.  I.e., send parts/car  transactions and negotiations as well as 
>other personal messages only to the  intended recipient, not to the Clubhouse 
>public address. This practice will  protect your privacy, reduce the total 
>volume of mail and fine tune the content  signal to Mopar topic.  Thanks!
> 
> 1962 to 1965 Mopar Clubhouse  Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and  
>http://www.1962to1965mopar.ornocar.com/general_disclaimer.html. 
>
> 
> 


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html. 












Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.