Re: heads

[Donnie Schanz Jr <dcs426@xxxxxxxxxxxxxx>]

Yes, the ports are huge when compared to a 426 S.W. or a 440. If you have an 
aftermarket intake or factory single four, you have 426 S.W. heads. There 
are no other intakes except the factory crossram and a few Indy pieces that 
fit.

Donnie
----- Original Message ----- 
From: "Donald Gallimore" <dongallimore@xxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Thursday, December 24, 2009 12:05 PM
Subject: Re: heads



> From Mopar Muscle:

Max Wedge heads are easily identifiable by the lack of a heat cross-over 
passage, large 1.88-inch exhaust valves, and very large ports. Casting 
numbers for the Max Wedge heads end in either 286, 209, or 518


Akron Don

There are no heat riser ports on a max wedge head. The area between the two 
center intake parts should have no openings.

Then there's the casting number which is located in the valve springs area. 
I'm sure there's a listing of head casting numbers somewhere on the 62-65 
website.

Akron Don




________________________________
From: Harry Skalla <moweepea@xxxxxxxxxxx>
To: 1962 1965 <1962to1965mopars@xxxxxxxxxx>
Sent: Thu, December 24, 2009 10:50:27 AM
Subject: heads


First of all Merry Christmas to all. I have a set of 426 heads on my car, 
how do I tell if they are Max Wedge heads or street wedge heads? Without 
taking them off.Thanks...Butch

----
Please address private mail -- mail of interest to only one person --  
directly to that person. I.e., send parts/car transactions and negotiations 
as well as other personal messages only to the intended recipient, not to 
the Clubhouse public address. This practice will protect your privacy, 
reduce the total volume of mail and fine tune the content signal to Mopar 
topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
--
[Non-text portions of this message have been removed]


----
Please address private mail -- mail of interest to only one person --  
directly to that person. I.e., send parts/car transactions and negotiations 
as well as other personal messages only to the intended recipient, not to 
the Clubhouse public address. This practice will protect your privacy, 
reduce the total volume of mail and fine tune the content signal to Mopar 
topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and 
http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.




________________________________

From: Donald Gallimore <dongallimore@xxxxxxx>
To: 1962to1965mopars@xxxxxxxxxx
Sent: Thu, December 24, 2009 11:39:30 AM
Subject: Re: heads

--
[Non-text portions of this message have been removed]


----
Please address private mail -- mail of interest to only one person --  
directly to that person.  I.e., send parts/car transactions and negotiations 
as well as other personal messages only to the intended recipient, not to 
the Clubhouse public address. This practice will protect your privacy, 
reduce the total volume of mail and fine tune the content signal to Mopar 
topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and 
http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.