Re: lazy man needs to change his leaf springs

JUST BLOCK THE YOKE WITH BLOCKS. IF YOU HAVE ANOTHER STAND JUST USE THAT

On Sun, Apr 17, 2022 at 9:30 AM neal zimmerman <neal.zimmerman@xxxxxxxxx> wrote:

OK ffolkes, I have a question for the experts here. Is it possible to change out the leaf springs on the 65 coronet while leaving the rear axle in place. The reason being is I don't want to crack open the T-block brake hose and have to bleed it all over again. It seems like it's possible but I want to make sure there's not something I am overlooking.
If I can separate the axle housing from the leaf springs and raise the axle housing up high ( with a jack) and rest the axle on jack stands to hold the axle housing while I install the leafs and then lower the housing back down onto leafs, it should work right? Of course I realize I need to have the car itself on stands as well before I begin,
One potential issue I see is that once I have the axle housing free, the weight of the pinion is going to want to swivel earthwards , so I need to figure out some sort of way to prevent that. Maybe I can build some sort of wooden jig that would go between the jack and the axle to prevent that.
Or is there a better way , or something I am overlooking?

Did I mention I really hate bleeding brakes!!
Neal Zimmerman

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/1962to1965mopars/CANQhizRLFWA5N7SEmoMqxrCL4EkDKSHxtbJ2Yend6hqp0XGOaw%40mail.gmail.com.

Gwwilson

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/1962to1965mopars/CAM_Vd%2BDYDnGgc9fp_9OcUpb9_DNE-TKWfHg%3D4B%3D_nZ44BVSr4Q%40mail.gmail.com.