I need a little help with my 64 Belv.
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

I need a little help with my 64 Belv.



===========================================================
Cancel your low-carb diet. Lose weight. Choose your own 
foods. Learn more about our program at:
caaccM7b7yoMza/ Dr. Smith
===========================================================

I got a reject inspection sticker yesterday for a few reasons and I'd
appreciate any help you folks can provide.
My cousin was slow at his repair station so I was able to "borrow" a lift
for a little while.  Case of beer rent.

My muffler has a hole on it right next to the exhaust connection.  The tail
side is beginning to come through as well.  It's the original exhaust.  The
muffler has a 9-63 date stamp.  The system is welded with a single clamp at
the crossover pipe - exhaust pipe connection.  Any suggestions for a correct
MOPAR muffler before I settle for a parts store universal one size fits all?
It's a poly engine, 34K original, single exhaust system.
I'm thinking of trying a patch for now as I have 30 days here in MA on the
"R" inspection to correct it.

Shocks are leaking, seals are gone.  They still work but time has dried them
out.  Are gas shocks what many of you have come to use?  It's strictly a
driver.

The center section was clean inside when I opened the fill plug but the
level was down. I could get a bent wire wet at about 1" down.  It should be
just below when on a frame lift.   Should I just top it off or suck it and
re-fill?  It's a 741 case, open gear (one wheel one way, the other
opposite), no ratio ID tag.  It was dirty but after spraying and wiping it
down, it doesn't appear to have any leaks.  Just SAE90 or is there something
better?

I need front strut rod bushings.  They're cracked and pieces are missing.
Any sources?  I was going to do the torsion bar bushings front and rear at
the same time.  I think these are on Ebay.  How do you set the torsion bars
for height and load before the lock nut is torqued?  I also need some help
with grease.  What do you guys use?  My cousin say's he used to use long
fiber.  What the heck is that?

I couldn't get the rear drums off to save my life.  I spooned them in as far
as I could and even whacked the drums out with a mallet but no go.  I didn't
want to break anything so I adjusted them back out until they rubbed the
drums and put the wheels back on.  Nice high pedal, stops fine (for manual
with a single master!) for now.  Am I doing something wrong?

There's a bunch of other stuff I think I can lick but these have me confused
beyond normal state.
I'm so happy to finally be driving something I don't want to do anything
else!

Tom Duross
back out for another long drive this afternoon....... (all smiles)....
I even setup another email address: 6t4belvedere@xxxxxxxxxxx

===========================================================
Sponsor a child today through Children International.  
Give a desperately poor child hope for a brighter future.
For only $18 a month you can make a difference!
caaccM4b7yoMzf/ Children's Int'l
===========================================================

----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 



b7yoMz. 










Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.