Re: {Chrysler 300} Re: Temp & Fuel gauges
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: {Chrysler 300} Re: Temp & Fuel gauges



Thanks for input.   I have the temp gauge working.

I am Going to re install the other fuel gauge.

There was a wire that left the wiper switch. 

Once I stalled the temp worked but not fuel. 

I have no tester in house.

Sent from Yahoo Mail on Android

On Sat, Dec 30, 2023 at 6:22 PM, 'dave mason' via Chrysler 300 Club International
<chrysler-300-club-international@xxxxxxxxxxxxxxxx> wrote:
Clean grounds as John says; also re-seat the 5-pin connector that feeds the circuit card on that side.  Sometimes a loose connection there can prevent either input voltage or gauge continuity.  You can ground the wire at the temp sender and see if the temp gauge starts going up.   Same for fuel- ground the wire at the sender and watch fuel gauge.  
Keep in mind that, since you replaced the fuel gauge, you have also replaced your limiter.   The voltage limiter feeding the fuel and temp gauges their 5V is inside the fuel gauge housing.  

You can check for +12V at the appropriate wire in the harness that terminates at the 5-pin connector.  I don’t recall the wire color but it should be at the circled pin here:

IMG_9761

As you face the dash while sitting in the driver seat it’s the second one from the right; if you look at the back of the instrument cluster it’s the second from the left.  Make sure you have 12V here.  

D&K

Sent from my iPhone

On Dec 30, 2023, at 17:21, John Grady <jkg@xxxxxxxxxxxxxxxxx> wrote:


sounds like no ground on metal or board ground , that plug .. Jump around ground pin to solid ground or solder pins to board 
see posts earlier this year .
Do not leave key on you will burn out gauges , regulator does not work if not grounded puts 12v on 5 v gauges burns them out . Why it pegs . 
Sent from my iPhone

On Dec 30, 2023, at 5:16 PM, Dave Dumais <dave.dumais@xxxxxxxxx> wrote:

Hello and Happy New Year.

I have successfully replaced the 64 speedometer, and it is a working unit.

However, the fuel and temp gauges were also replaced. 


Both gauges peg to left during operation,
And the high beam indicator does not function.

Believing that all elect. connections are correct
Any thoughts or experiences? 

Thanks
Dave D

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/07CAC1B2-A05C-43A6-A40F-B6E1DBA3022B%40gradyresearch.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/40E7D75F-74B0-48CA-A811-B0BD43A84CDE%40yahoo.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/1459482919.3907165.1704050566985%40mail.yahoo.com.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.