RE: {Chrysler 300} 1964 Chrysler front bumper

Mel, Hold the thought for a week or so. We are going to try and heat the bracket and see if we can get it to shape. If so, I will then weld the bottom down to the bumper. If not, then I will call you about the bracket.

James

From: melvin stoltzman <mlstoltzman@xxxxxxxxxxx>
Sent: Thursday, July 27, 2023 14:47
To: James Douglas <jdd@xxxxxxxxxx>
Subject: RE: {Chrysler 300} 1964 Chrysler front bumper

Hi James

Will the bracket work for you on this bumper I can remove the bracket from the bumper any questions call me@

651-271-2064

Thanks

Mel Stoltzman

From: 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Sent: Tuesday, July 25, 2023 8:24 PM
To: D.C. Mason <petergriffinforpresident@xxxxxxxxx>
Cc: melvin stoltzman <mlstoltzman@xxxxxxxxxxx>; Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: RE: {Chrysler 300} 1964 Chrysler front bumper

This one looks close. Attached are a set with my good side and bad side. What is hard to tell in the photo is how the bad one is bent at the top and even heating it would be tough to get the correct shape.

A good one that has not been bent would be better. Since I have to weld one side no matter what, welding the top and bottom would be a better option. I think the length was about 8 -1/4 inches in length.

James

From: D.C. Mason <petergriffinforpresident@xxxxxxxxx>
Sent: Saturday, July 22, 2023 12:58
To: James Douglas <jdd@xxxxxxxxxx>
Cc: melvin stoltzman <mlstoltzman@xxxxxxxxxxx>; Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: Re: {Chrysler 300} 1964 Chrysler front bumper

James,

Is this what you need?

D&K

Sent from my iPhone

On Jul 21, 2023, at 11:58 PM, 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx> wrote:

Hi Mel, No. What I need is the bracket that is spot welded by the factory to the outer end of the front bumper. It is about 6 inches long and perpendicular to the length of the bumper. I suspect that something hit the bumper and pushed this back against the spring steel bracket that you are referring to.

I could try and drill out the three remaining spot welds and straighten the bracket and then weld it back but if I can fine a good one…that would be easier.

I am out of town and when I get back I will post a photo.

James

From: melvin stoltzman <mlstoltzman@xxxxxxxxxxx>
Sent: Friday, July 21, 2023 13:05
To: James Douglas <jdd@xxxxxxxxxx>
Cc: mlstoltzman@xxxxxxxxxxx
Subject: RE: {Chrysler 300} 1964 Chrysler front bumper

I have the bracket from the frame to the bumper that I took off a 1964 300K is that what your are looking for.

Mel Stoltzman

From: 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Sent: Thursday, July 20, 2023 2:05 PM
To: Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: {Chrysler 300} 1964 Chrysler front bumper

Anyone have a VERY bad front bumper that the front passenger side bracket, the one on the bumper not the spring steel one, in good shape? If so, I would like to pay you if you can cut it away from the bumper and ship it to me.

I have one that is bent, and I used by jaws to pry it out and on the last push the lower three spot welds popped. I could heat and pound it to shape but drilling the top three spot welds and then rewelding a good bracket, on the backside with heat cream on the front side, is less time and would have a better outcome.

Thanks, James

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB6171936139266F2B4BD3096E933EA%40CY5PR19MB6171.namprd19.prod.outlook.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB61712E01E79CD31DA7D0D3C3933CA%40CY5PR19MB6171.namprd19.prod.outlook.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB6171EA7298293A229020F5739300A%40CY5PR19MB6171.namprd19.prod.outlook.com.