RE: {Chrysler 300} Request Somewhat time sensitive 300K radio
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: {Chrysler 300} Request Somewhat time sensitive 300K radio



Thanks Guys,

 

Since I have the entire cluster out…

 

I pulled the tape off the top of the plastic and sure enough they plugged it directly to the back of the fuse spade.

 

I am going to make up a 18 inch wire to place on that spade with a connector so one can pull the radio out and then just disconnect the wire.

 

Now I have another issue.  I pulled that vacuum can off the actuator door and tested  it and it works.

 

BUT…

 

There are two large NUTS used as spacers on the shaft of the vacuum can to the mounting bracket. It does NOT look like the one in the service manual as it pulls/pushes up and down and not side to side.

 

I have some vague memory of seeing this on my other 300K.  Can anyone tell me if this is a factory “fix”.

 

Also, when installed and the engine off is the door supposed to be closed or open on AC cars.  The “over-center” on the door only locks on open not on closed.

 

If anyone can enlighten me, please do.

 

Thanks all, James.

 

From: Rich Barber <c300@xxxxxxx>
Sent: Wednesday, March 15, 2023 18:01
To: James Douglas <jdd@xxxxxxxxxx>
Subject: RE: {Chrysler 300} Request Somewhat time sensitive 300K radio

 

My recollection is that there are a number of connections to my Touch-Tuner seven-button AM radio. Hot wire from “RADIO” fuse, a wire from the dimmer circuit for the lights, antenna cable, wires out  for front speaker and to the reverb/back speaker switch and a pair of wires with a plug connector to a foot-operated switch to change stations.  All had easy disconnects or connectors to “facilitate” removal.  Should be no need to add a hot wire to fusebox.

 

 

I have several instrument panels with PC boards & etc. if you come up short.  Also some ideas to assure good performance of the boards if needed.

 

Rich Barber

Acting Director

Chrysler 300 Club, Inc.

1801 Redwine Terrace

Brentwood CA 94513-6000

c300@xxxxxxx

(H) 925-513-6583

(M) 925-783-4893

www.chrysler300clubinc.com

 

 

 

 

 

From: 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Sent: Wednesday, March 15, 2023 5:16 PM
To: Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: {Chrysler 300} Request Somewhat time sensitive 300K radio
Importance: High

 

Hi All,

 

We have had a break in the rain here in San Francisco. I decided to pull the dash here, rather than up at my place with more, now I have can of worms. I wanted to replace the circuit boards on the cluster with the new manufacture ones I pickup off of eBay.

 

I took out the speaker as I want to look at the wiper assembly and to check the ventilator door. Turn out the vent door screw are loose and so the door is not operating as it should.

 

The screws on the door vacuum bracket angle down and there is no way to get a screwdriver on there, I did try an angle one, with the radio in.

 

So, I go to pull the radio and it will not come out. AM. 

 

There is a wire that does not have a disconnect and it looks like it is going into the back of the fuse box. Why the hell would the factory hard wire that in?

 

In any event, do I have to pry the plastic off the back of the fuse box to see if there is a connector in there or is it better to just cut the wire and plan on creating a wire coupling.

 

I have about an hour or so of light left. If anyone is reading this now (17:13 hours pacific) and can advise, please do…thanks.

 

James

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB617179C392BA8228748EA84493BC9%40CY5PR19MB6171.namprd19.prod.outlook.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB617134D719F38B5E2BA958F893BC9%40CY5PR19MB6171.namprd19.prod.outlook.com.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.