RE: {Chrysler 300} 300K hub caps

The wheel cover painting trick I’ve used for my G (very similar cover) is to take a piece of quality printer paper, I use 11 x 17 ledger paper because I have it on hand, and roll it in a circle and set it into the recess in the cover. Mark the point that it fits and masks nicely, remove it, and tape it to itself top and bottom making a cylinder shape. Set into prepared wheel cover and spray into the cylinder covering the bottom as the factory did. Easy, and no masking tape involved. You can also use thin plastic sheet if you have it, I’ve done it both ways. Sorry I don’t have a picture handy.

Bob J

From: 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Sent: Friday, January 20, 2023 9:25 AM
To: Nick Taylor <nicksgaragesd@xxxxxxxxx>
Cc: Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: RE: {Chrysler 300} 300K hub caps

Thanks Nick, That is a process I had not thought of! James

From: Nick Taylor <nicksgaragesd@xxxxxxxxx>
Sent: Friday, January 20, 2023 09:02
To: James Douglas <jdd@xxxxxxxxxx>
Cc: Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: Re: {Chrysler 300} 300K hub caps

I've used this method for painting emblems and other things, maybe it would work.

Mask off the major part of the wheel cover. Paint the colored areas with a few light coats until you get the coverage you need. Then use acetone (I use nail polish remover) on a cloth and carefully remove the paint from the ribs in the painted sections and any overspray.

I used this method on my 300F wheel covers when I was repainting the red. It looks like it would be simple to mask them off but the tapered cone shape is tough, so a little paint got up the sides. Got nice clean line by using the acetone to remove the overspray.

On Fri, Jan 20, 2023 at 8:48 AM 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx> wrote:

Has anyone come up with a process to replicate the silver paint on the 300K hubcaps?

The work involved to mask it would be a PITA.

My car did not have the hubcaps, so I had to buy some from eBay. A couple of extra caps I picked up that were in better shape are not 300 caps, but I can switch the medallions. But I need to make them all the same paint color. Other than that, I could just strip them, polish them, and call it a day.

Or perhaps there is someone out there that specialized in hub cap restoration?

Thanks, James

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB617196B5C881E14852DD034993C59%40CY5PR19MB6171.namprd19.prod.outlook.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB6171C35AA9F63B1E6E84249993C59%40CY5PR19MB6171.namprd19.prod.outlook.com.