Re: {Chrysler 300} Re: Actually Pulling the Steering Chuck…
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: {Chrysler 300} Re: Actually Pulling the Steering Chuck…



We had another way to ground that much better without the strap , which often goes intermittent . = very Poor design at best .
I think I drilled and tapped like 6/32 for a real hi flex silicone jumper wire soldered into eyelets around the rubber . 
May be on 300 tech info somewhere ?? 
Was long ago 
John 

Sent from my iPhone

On Jan 8, 2023, at 9:38 AM, 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx> wrote:


Yesterday I put in the temporary unit, and I was able to get it in without having to take the spool valve off the chuck. I did however find that to get it to rotate into the big hole in the firewall and clear the control arm that I needed to get the starter cables out of the way.

It may be that the cables were changed at some point and the length is a little shorter. In any case the reason I could not get it out as the rotation angle could not be achieved with the cable connected. A FYI to anyone pulling the chuck on a '64 is to take the starter cables off the starter it will make your life easier.

Of course, now I am at a dead stop as the copper grounding strap is shot. I drove around yesterday to three auto parts stores, two hardware stores, Lowes and Home Depot. None of them had an .005 copper sheet (shim stock). 

So, I will have to head back to SF without the job done. Order some copper stock from McMaster-Carr and come back in a week and finish the job.

On the subject of the ground strap. I seem to remember the last time I did this that I did NOT slice the replacement rubber at the top as that is the spot where the rubber fails.  I think I ran the strap out the upper and and around and it worked fine. 

Bob, or anyone else, can you think of any reason that this is a bad idea? I would prefer not to slit the top of the rubber isolator which leaves that one side with very little meat where it connects at the base. The old one failed at that point.

James

From: 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Sent: Friday, January 6, 2023 18:50
To: Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: {Chrysler 300} Actually Pulling the Steering Chuck…
 
Hi All,

I may be an idiot, but I do not remember having such a hard time getting the box to come out. I tried and tried to do it the way the manual tells you to but I could not get the thing out.

I pulled the power booster and it still would not come out. I think someone replaced the booster and put the clamp on the bottom and so the spool valve was hitting that.

Even with the booster out I could not get it out. I finally had to pull the spool valve off the top of the chuck to get it to clear.

Now the last time I did this my back was in its mid 20's and now it is in its mid 60's and had had 5 hours of surgery so I was trying to not push it, but really what am I doing wrong as it was a PITA to back up, tilt the end up and get out.

Is the manual BS on 1964 or am I missing something?

James

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB6171FEB0E308122B58A36CD493F89%40CY5PR19MB6171.namprd19.prod.outlook.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB617176B26304E33DC03FF08A93F99%40CY5PR19MB6171.namprd19.prod.outlook.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/0EA0945A-D55E-450A-A577-B2F67093A397%40gradyresearch.com.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.