RE: {Chrysler 300} Distributor wiring

Hello Bill

Trick is to rework the canister arm. A new La canister connects via a pin small axle/pin. This is not the case on my original ibk dist braker plate. So carfully grind off the ridge that has been pressed for holding the pin on the arm, remove pin & now you have a mounting hole that will work.

Carfully rework the bends/angle of the arm so it will fit the original pin on the braker plate.

I was so exited when i made my first one i damaged it...no problem there are plenty new ones out there! take your time bending,,i did minor grinding awell.

Mounting holes on la will work as the dist outside radius is the same or 98%same. Check arms on pics i think you got it..

My old text;

Whats wrong with dual points?
300c Ibk-4304 almost done!
Vacuum advance absolute since long.. I reworked an vc-155can,,not that dumb as it deliver 10degree advance,,,std unit offer 11 tuned by shims! Both pulls at 9hg vaccum.
I will probebly not do another one,,,live & learn thing. If you go this route check part sum-850426 & with this you can adjust vaccum timing..nice part i ordered one but still waiting for it so just went on doing my work.. .....
Mine bench tested today worked fine!
Yes i hav a few brand new electronic dist so please no comments on why doing this please!
The show must go on!
/M

Skickat från min Samsung Galaxy-smartphone.

-------- Originalmeddelande --------

Från: 'bill grieve' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>

Datum: 2020-11-03 02:08 (GMT+01:00)

Till: chrysler-300-club-international@xxxxxxxxxxxxxxxx

Ämne: RE: {Chrysler 300} Distributor wiring

Nice how did you modify an LA can to work? I need a vacuum can for my 300H distributor. Thanks. Bill G.

Sent from Yahoo Mail on Android

On Mon, Nov 2, 2020 at 2:15 PM, micke.sundbom
<micke.sundbom@xxxxxxxxx> wrote:

Dennis, i did mine this summer. Totaly restored, with a modified La waccum can.
For wires i looked for same quality that comes with a quality multimeter test probes , so all new silicon wires, high heat resistant. Worked as a charm!
Thanks Michael

Skickat från min Samsung Galaxy-smartphone.

-------- Originalmeddelande --------
Från: "Williamson, Dennis G" <Dennis.G.Williamson@xxxxxxxxxx>
Datum: 2020-11-02 13:12 (GMT+01:00)
Till: chrysler-300-club-international@xxxxxxxxxxxxxxxx
Ämne: {Chrysler 300} Distributor wiring

Hi All,

Does anyone have a recommendation on a specific wire type to be used when rebuilding a 57 300C distributor? I am looking for a very flexible wire to renew all the internal wiring, ground strap to plate, power wires to points.

Dennis Williamson

Manteca CA.

NOTICE: The information contained in this message is intended only for the personal and confidential use of the recipients named above. This message is privileged and confidential. If the reader of this message is not the intended recipient, you are hereby notified that you have received this document in error and that any review, dissemination, distribution, or copying of this message is strictly prohibited. If you have received this communication in error, please notify the sender immediately and delete the message from your system

--
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/8825d707dad04f718a9918d7efd95c66%40snapon.com.

--
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/5fa068be.1c69fb81.e41e1.7c54%40mx.google.com.

--
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/1640819641.981302.1604365679203%40mail.yahoo.com.