Re: [Chrysler300] RAM Charger Intake ?

On Tue, Sep 17, 2019 at 11:23 PM 'Bob Jasinski' rpjasin@xxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

I have to second Noel on a “thumbs” up for the Lectric Limited wire set for my 300G. I installed it in 2011, it fit perfect and I have had zero issues. I do have all my heat shields in place, it came with a well written chart indicating the exact length of each wire, type of nipple and placement.

Bob J

From: Chrysler300@xxxxxxxxxxxxxxx <Chrysler300@xxxxxxxxxxxxxxx> On Behalf Of Noel Hastalis cpaviper@xxxxxxxxxxx [Chrysler300]
Sent: Tuesday, September 17, 2019 7:53 PM
To: cv300g@xxxxxxxxx; cv300g@xxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx>; Chrysler300@xxxxxxxxxxxxxxx
Subject: Re: [Chrysler300] RAM Charger Intake ?

Hello Charlie,

For my F, I've purchased 3 sets from Lectric Limited. I've had issues with not having the plug wire shields on my motor for the first several years, so burned the #5 and #6 wires a couple times. The part number for the F 'ramcharger' is #6302-000. Looking at their site just now, I see that they offer #6302-000 and #6302-611 for the '61 'ramcharger,' which is just their terminology for our ram induction / crossram cars, and not a marketing or technical term that Chrysler used. The plug wires' lengths are good - should fit in your 10 plug wire brackets. About 10 years ago, I ordered my first set of plug wires from Atlas, out in California, and the lengths of those wires were wildly different from what they should have been, so I've gone to Lectric Limited since then.

Since Lectric Limited is near Midway Airport, and only 15 minutes from my home, I've just driven over to their shop to pick up the plug wire sets, as I've needed to replace them. They've always had them ready for pickup the same day, or next day.

I'm not sure, but assuming the only difference between their #6302-000 and #6302-611 is the coding stenciled onto the wires, and not differences in the lengths of the wires. As they indicate on their website, #6302-611 is for cars dated 1-Q-61, which I'm guessing is for '61s actually built in '61.

Noel Hastalis
F Coupe
Burr Ridge, IL
On September 17, 2019 at 8:11 PM "cv300g@xxxxxxxxx [Chrysler300]" <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

Has anyone ordered the Spark Plug Wire set , #6302-611 , for the 300G through Lectric Limited ? Are all the wires the correct length to route in the proper manner and connect with the 10- Spark Plug Wire Brackets ?

Has anyone ever heard the , Ram Induction, Cross Ram ( Long Ram ) Intake referenced as the Ram Charger Intake?
In all my years I have never heard of it called a Ram Charger Intake .

The reason I am asking is I went to the Lectric Limited website and ordered plug wires for a 300G.
I ordered set 6302-611 which according to them is for a 1961 Newport, New Yorker, Town & Country and 300.
The description says : " V8 - all With Ram Charger Intake ".

While I assumed the wires were for the Cross ram Intake I asked a question when I ordered.
" Comment/PO Number: In this wire set is Each wire the correct length to install properly on all TEN spark plug brackets on the 1961 413 Cross Ram engine. ? If not cancel this order."

They acknowledged my order with an email saying:
" ORDER STATUS: Great news! It appears that your entire order is in stock and will ship within one business day. SHIPPING: After your order has been shipped, you will receive an email with your tracking number, directly from UPS. "

Well I waited and waited and finally emailed them asking where my order was. Their reply was " This order was cancelled due to your comments that we weren’t able to make the set as you wanted. ".

So I called them and they said they didn't know if the wires were correct for routing through the 10 Brackets and that's why the order was cancelled.

If that set is correct I'll have to odrer them again.

Charlie Valentine