Re: [Chrysler300] Kepich exhaust for 300E

["Charlie Valentine" <cross.ram@xxxxxxxxxxx>]

I used Waldron's and had excellent results. I ordered stainless steel dual exhaust, front to back , for my 62 300 Sport. 
I installed it and the right side was too close to the frame. I called and he said "just get out your torch and heat it and bend it". I told him that I do not have a torch, which I don't, and he sent me another pipe which clears the frame.
Below is a link with his phone numbers. Call him to see if he can make them for the "E".

As far as the Stainless Steel pipes available thru Eileen Brass. Heard many complaints that they do not fit well. Tis a pity to have the bended bend pipes that do not fit well. Can someone close to her find out where the problem is and get it corrected?

Charlie Valentine

http://ll.hemmings.com/pdfs/WaldronsE64141.pdf#search=%22waldron%20Exhaust%22
  ----- Original Message ----- 
  From: John J. Hertog 
  To: 'Henry Hopkins' ; chrysler300@xxxxxxxxxxxxxxx 
  Sent: Monday, September 18, 2006 1:26 PM
  Subject: RE: [Chrysler300] Kepich exhaust for 300E


  I will agree with Henry, and say that I have all my exhaust systems done by
  a local shop. They key is finding a local shop where the owner cares, and
  does good work. I am fortunate to have such a shop in my area. He knows how
  to use a bender and creates, from scratch, beautiful systems that fit well,
  look right, and are priced right. Considering all I have to do is drop off
  the car and pick it up when done, the average cost of about $400, front to
  rear, all new, installed, no fuss, is well justified. 

  The only "exception" to my using a local shop is the ram exhaust system
  (forward 5 pipes) which I always purchase from Eileen Brass; those are good
  pipes, well-made, and fit well (as long as not stainless! ) 

  John Hertog
  Sag Harbor NY 

  _____ 

  From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On
  Behalf Of Henry Hopkins
  Sent: Monday, September 18, 2006 12:00 PM
  To: chrysler300@xxxxxxxxxxxxxxx
  Subject: Re: [Chrysler300] Kepich exhaust for 300E

  We say some good, some bad. Bit faster than others but we've had problems 
  with the header pipe on one. Now we have a local shop make up and install a 
  system. In the past, installing the kits ourselves didn't work because 
  bends were not quite right, pipes hitting the frame, etc. Had to bang dents 
  in the pipes here and there to stop the pipes hitting the frame after 
  getting tired of the rattles.

  Our two cents, Henry Hopkins/Richard Palmer
  ----- Original Message ----- 
  From: "John J. Hertog" <crossram@optonline.
  <mailto:crossram%40optonline.net> net>
  To: <chrysler300@ <mailto:chrysler300%40yahoogroups.com> yahoogroups.com>;
  "'jdelrae1'" <jdelrae1@cox. <mailto:jdelrae1%40cox.net> net>
  Sent: Monday, September 18, 2006 5:16 AM
  Subject: [Chrysler300] Kepich exhaust for 300E

  > Hi Jim, and all
  >
  > Jim, you are now hitched up to the listserver. Welcome aboard. As far as
  > Kepich, I think the feedback you will receive from most folks is that they
  > are pretty bad... both in terms of their product, and also their attitude.
  >
  > Any comments from membership? what would be a good source for 300E 
  > exhaust
  > system ?
  >
  >
  > John
  >
  >
  >
  > _____
  >
  > From: jdelrae1 [mailto:jdelrae1@cox. <mailto:jdelrae1%40cox.net> net]
  > Sent: Sunday, September 17, 2006 9:42 PM
  > To: John J. Hertog
  > Subject: Re: Hello
  >
  >
  > Hello John,
  > Thanks for the information.. I did end up figuring out the system I
  > ordered was not the correct system. It was about 3' to long I used Kepich
  > Exhaust they were in the clubs listing for resources. I'll keep you 
  > posted
  > on how this turns out. I am not real happy with them so far since I 
  > called
  > them on Saturday when I was having problems and he said they were closed 
  > and
  > to call back on Monday?
  > Thanks!
  > Jim
  >
  > ----- Original Message ----- 
  > From: John J. <mailto:crossram@optonline.
  <mailto:crossram%40optonline.net> net> Hertog
  > To: 'jdelrae1' <mailto:jdelrae1@cox. <mailto:jdelrae1%40cox.net> net>
  > Cc: 'Bob Merritt' <mailto:bob@simplexco. <mailto:bob%40simplexco.com> com>
  > Sent: Sunday, September 17, 2006 7:09 PM
  > Subject: RE: Hello
  >
  > Hi Jim,
  >
  > We should have you up and runnign on the listserver tomorrow (Monday) . 
  > In
  > the interim, I posted your question to the group, and rec'd this response
  > from Steve Albu:
  >
  >
  > Jim, you might want to let the club members know from whom you obtained 
  > the
  > exhaust system. With some rare exceptions, when you order these systems
  > through the mail, they will not fit most of the time. The bends are
  > critical, and it takes someone with good equipment and skill to make them
  > mail order.
  > Steve Albu
  >
  >
  >
  > ---- "John J. Hertog" <crossram@optonline.
  > <BLOCKED::mailto:crossram@optonline. <mailto:crossram%40optonline.net>
  net> net> wrote:
  >> Hi to all,
  >>
  >> Jim is a new member.. can someone please help him with regards to his
  >> question?
  >> 300'ly to all
  >>
  >> John Hertog
  >> Sag Harbor NY
  >>
  >> _____
  >>
  >> From: jdelrae1 [mailto:jdelrae1@cox. <BLOCKED::mailto:jdelrae1@cox.
  <mailto:jdelrae1%40cox.net> net>
  > net]
  >> Sent: Sunday, September 17, 2006 5:11 PM
  >> To: John J. Hertog
  >> Subject: Hello
  >>
  >>
  >> Hello John,
  >> I was wondering if you had or knew anybody that may have a photo of the
  >> under carriage of a 59E. I purchased an exhaust system for my E and am at
  >> wits end trying to install it. Mine did not have a system when I 
  >> purchased
  >> it and the new system had no information when I received it. Spent the
  > last
  >> 2 day re configureing the pieces to the new system and am still
  >> unsuccessfull getting this mess together. Any information would be
  >> appreciated.
  >> Thanks,
  >> Jim DelRae
  >>
  >
  >
  > _____
  >
  > From: jdelrae1 [mailto:jdelrae1@cox. <mailto:jdelrae1%40cox.net> net]
  > Sent: Sunday, September 17, 2006 5:11 PM
  > To: John J. Hertog
  > Subject: Hello
  >
  >
  > Hello John,
  > I was wondering if you had or knew anybody that may have a photo of the
  > under carriage of a 59E. I purchased an exhaust system for my E and am at
  > wits end trying to install it. Mine did not have a system when I 
  > purchased
  > it and the new system had no information when I received it. Spent the 
  > last
  > 2 day re configureing the pieces to the new system and am still
  > unsuccessfull getting this mess together. Any information would be
  > appreciated.
  > Thanks,
  > Jim DelRae
  >
  >
  >
  > [Non-text portions of this message have been removed]
  >
  >
  >
  > To send a message to this group, send an email to:
  > Chrysler300@ <mailto:Chrysler300%40yahoogroups.com> yahoogroups.com
  >
  > For list server instructions, go to 
  > http://www.chrysler <http://www.chrysler300club.com/yahoolist/inst.htm>
  300club.com/yahoolist/inst.htm
  >
  > For archives go to http://www.forwardl
  <http://www.forwardlook.net/300-archive/> ook.net/300-archive/
  > Yahoo! Groups Links
  >
  >
  >
  >
  >
  >
  >
  >
  >
  >
  > 

  [Non-text portions of this message have been removed]



   

[Non-text portions of this message have been removed]



To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/ 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    mailto:Chrysler300-digest@xxxxxxxxxxxxxxx 
    mailto:Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/