Wheel Alignment Gauge

Now you can check wheel alignment in minutes. Tool measures toe-in and toe-out on an easy to read gauge. Lets you adjust alignment to minimize tire wear. Even checks wheel wobble. To use, set gauge at rear of front tires and take measurements. Transfer tool to front and measure the difference. If necessary, adjust tie rods in or out half the distance of the dial reading.

Brake Drum Reset Gauge

Determines proper clearance between brake lining and drum. Outside calipers transfer measurement to brake shoes. Inside calipers measure drum diameter. Locking nut holds reading.

Brake Light Switch - Pressure

BRAKE LIGHT SWITCH - PRESSURE #80171 - Hydraulic brake light switch - 1/8" pipe thread fitting.

Brake Light Switch- Push Button

BRAKE LIGHT SWITCH - PUSH BUTTON #80172 - Pedal/linkage activated switch.

Eezibleed Brake & Clutch Bleeder Kit

Bleed Brakes/Hydraulic Clutches with Pressure - Pressure works better than vacuum because air is not pulled around the bleed fitting. Eezibleed uses a tire or tank set at 20 psi with the included reservoir bottle to inject fresh fluid into the master cylinder as the system is bled. Fits most imported cars. Can fit any vehicle by modifying a spare master cylinder cap by drilling a 3/8" hole and attaching the pressure/fluid hose with the included hardware. Includes pressurizing hose with tire stem fitting, assorted caps to fit many Lockheed and Girling systems, and instructions. Made in the UK.

Hub and Axle Puller - Heavy Duty

Heavy Duty. Hardened steel pulling screw. Simplifies removal of rear hub and drum. A must when pulling a wheel!  Includes special wrench to turn screw. Pulling strength: 30,000 psi. #51UL0236Y

Read more about this puller in the Forward Look Archives

Hub and Axle Puller

HUB PULLER. Lighter duty. For American and imported front-wheel-drive cars and light trucks with 4- and 5-bolt stud patterns. Simplifies front wheel brake and bearing maintenance. Applications: All Makes All Models

Mityvac Brake Bleeding Kit

Vacuum tester/brake bleeding kit gives you a clean, quick way to bleed the fluid lines in your vehicles brake system. May also be used on virtually all hydraulic systems! Trigger release for one-hand operation. Reservoir jar creates a vacuum that pulls fluid into the jar with the fluid comes the air bubbles. Includes 24in. of 1/4in. I.D. tubing, rubber cup adapter, reservoir jar storage lid and 40-page instruction book in Spanish and English.

Mityvac Plus Test Kit

Same features as above plus the benefit of a switch-valve for quick change from pressure to vacuum testing without changing hose positions. Comes complete with attachments, caps, jar, hoses, master cylinder kit, and detailed instruction manual.

Phoenix V12 Brake and Clutch Bleeder

Purge trapped air in brake and clutch hydraulic using patented Reverse Fluid Injection technology without a helper and in about 10 minutes. Works on cars, trucks and motorcycles where manual methods and conventional pressure bleeders fail! Includes brake fluid bottle adapter, quick couplers and hoses and instructions. Compatible with all brake fluids.

Tubing Bender General Purpose

Heavy-duty quality construction. Doesn't collapse or distort tubing. Bends 3/16", 1/4", 5/16" and 3/8" diameter tubing.

Tubing Bender Rolling

For smaller diameter (3/16" and 1/4" O.D.) coated tubing, use the rolling action tubing bender. It utilizes a free-rolling follower CAM to minimize stretching and distortion when bending tubing. This produces uniform, distortion-free, tight, 180 bends down to a 1" radius. Will not harm protective surface coatings on fuel and brake lines. Comes apart for easy placement over long pieces of tubing. For bench use, a tab is provided on the lower handle.

Tubing Bender Set Rolling And Heavy Duty

Here are 2 essential tools when forming coated tubing: rolling action tubing bender (3/16" and 1/4" O.D.) and heavy-duty tubing bender (5/16" and 3/8" O.D.) for thick walled tubing. Both utilize a free-rolling follower CAM to minimize stretching and distortion. Will not harm protective surface coating on fuel and brake lines. Comes apart easily for easy placement over long pieces of tubing. Made in England.

Tubing Cutter

Roller Cutter with micrometer-style adjuster, flare cut-off groove.

Tubing Flaring Kit Double Single

Fabricate double-compression lines (brake) or single-compression lines (fuel, etc.) in steel, aluminum, or copper. Not recommended for stainless or tubing walls thicker than 0.040". Handles 3/16", 1/4", 5/16", 3/8" and 1/2" O.D. tubing. Limited 1 Year Manufacturer's Warranty.

Hog Ring Pliers Bent Nose

These pliers are the basic tools needed to do upholstery work. Designed just for hog ring installation. Grooved jaws hold the ring securely. The straight pliers are spring loaded to hold rings closed. The angled pliers are spring loaded to stay open. Forged steel with safety grips.

Hog Ring Pliers Straight Nose

These Pliers are the basic tools needed to do upholstery work. Designed just for hog ring installation. Grooved jaws hold the ring securely. The straight pliers are spring-loaded to hold rings closed. The angled are spring-loaded to stay open. Forged steel with saftey grips.

Hog Rings - Pack of 100

Pack of 100 Hog Rings

Steering Wheel Puller

Steering Wheel Puller

Window Regulator and Door Handle Remover

For use on AMC, Chrysler, Ford and GM vehicles. Use the narrow end.

"Versatile tool has a semi-sharp edge for removing moulding, clips, badges and much more."

Ten In One Trim Tool

Ten uses: 1. Serrated edge for panel seam cleanup. 2. Door clip removal. 3. Windshield molding clip release. 4. Headlight spring tool. 5. Handle remover. 6. Trim pad removal. 7. Weather strip clip removal. 8. Door trim clip installation. 9. 1/2" wrench for wipers. 10. Beveled edge for molding removal. Made of tempered spring steel.

Trim Removal Set All Three Tools

There are many slips, retainers and fasteners to be removed during interior work. These tools fit most cars and get the job done right. A. Door panel clip lifter protects door panels while removing the clip. B. Window handles use special wire clips that are difficult to remove without this tool. C. Windshield molding clips are quickly disengaged with this hook.