Martin Senour (and most of the other major paint brands probably have
something like it) has a product called "QuickSeal" that is advertised as
providing corrosion protection for short-term outdoor storage. If you
follow the directions and apply it properly, then when you are ready later
to complete the job, you can sand this coat of sealer, and continue on with
applications of primer and topcoat.
Tim
Stellar Antique Auto Restorations
----- Original Message -----
From: "Bill K." <pontiac@xxxxxxxxxxxxxx>
To: <L-FORWARDLOOK@xxxxxxxxxxxxx>
Sent: Sunday, December 19, 2004 6:30 PM
Subject: Re: [FWDLK] Types of primer
> The problem with primer is it's porous - moisture can get through it to
the
> metal, because it's made to be that way so paint will stick to it. If
your
> car was stored the entire winter in a heated, climate controlled garage -
it
> would probably be okay to just prime it or even oil it down (WD40 would
even
> work). But if you drive it, or let it be subject to temperature changes
> that would cause condensation, it will get some moisture into it and that
is
> what causes rust.
>
> If I were doing this depending on my budget I'd hit it with the etching
> primer, a primer surfacer (available in a spray can for about $5 at Pep
> Boys) and either a plain top coat in a compatible color, out of a rattle
> can, or a sealer. Then so long as it's not out in the weather it should
> stay fine - the key is sealing the primer once it's there. But if you're
> not going to do any sanding or prep, you'll want the primer surfacer under
> there so that when you finally do sand it, there's a little more paint
there
> before you sand through to the metal. If you expect to have to sand
through
> to the metal anyways, you could probably skip this step and just seal it
> over the etching primer - if you sand a hole in that, you just prime with
it
> on that spot again. Odds are whatever color you put on there will mostly
be
> sanded away, but I'd get something close color wise or plan to seal it if
> there is any paint left just in case - no sense having it bleed through
> later.
>
> Just FWIW, my Suburban has heavy rust in the wheelwells in back. I wire
> brushed most of the spots and hit them with a sanding wheel, primed them
and
> coated them with some cheap paint. In just a few weeks of weather (and
with
> very little actual driving as I went through a nightmare brake rebuild)
the
> rust is starting to come through some spots already, mainly on edges where
> it already rusted through. Granted this was just a rattle can job
because
> it was too cold outside to do it right, and I know on this thing it's
> probably going to be a losing battle to fight the rot anyhow - but it
still
> doesn't take long if the moisture can find it's way into the metal.
>
>
>
> Bill K.
>
>
> ----- Original Message -----
> From: "Lou" <email4lou@xxxxxxxxxx>
> To: <L-FORWARDLOOK@xxxxxxxxxxxxx>
> Sent: Sunday, December 19, 2004 2:59 PM
> Subject: Re: [FWDLK] Types of primer
>
>
> > I've been told its almost futile to try it that way since you'll have to
> > re-sand and re-prime anyway due to dirt, nicks, bugs, etc. There are
> > also the concepts of "chemical bonding and mechanical bonding...to get
> > certain paints to stick properly to certain pimers, there is a time
> > window of opportunity (chemical bonding). When the primer has cured too
> > long, then you have to sand re-primer before you paint. The
> > recommendation I got was to use whichever primer you want, then paint
> > over it with a coat of the appropriate type of paint for
> > protection...even stuff in a rattle can. (color doesn't matter since you
> > just want to cover it). I tried using epoxy primer and leaving
> > uncovered and I drove the car. just a month or so later, the coating
> > and the panel underneath it was starting to deteriorate.
> >
> > Dave & Tracy wrote:
> >
> > >What is the consensus on using a zinc primer on bare metal ? . I know
> that traditionally it should be etch primer filler primer, topcoat.
However
> I need to paint some sheet steel on the new rear driverside quarter with
out
> painting other coats etc. So I am looking for a type of primer that is
over
> paintable at a latter date. could do with something that when dry is as
hard
> as Iron, to give max protection over the winter..
> > >Dave.
> > >
> > >*************************************************************
> > >
> > >To unsubscribe or set your subscription options, please go to
> > >http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1
> > >
> > >
> > >
> >
> > *************************************************************
> >
> > To unsubscribe or set your subscription options, please go to
> > http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1
> >
>
>
> ---
> Outgoing mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.813 / Virus Database: 553 - Release Date: 12/14/2004
>
> *************************************************************
>
> To unsubscribe or set your subscription options, please go to
> http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1
*************************************************************
To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1
|
|
Back to the Home of the Forward Look Network