Re: [FWDLK] Degreaser

[Scott H <kneedrager@xxxxxxxxxxx>]

I always liked GUNK foaming engine cleaner.  It does a pretty good job.  I
recently found something called "Purple Power" in Advance Auto Parts. Comes
in a 1 Gal container and was less than $5 works great for soaking parts and
you could put it in a spray bottle and apply it to an engine.  It took
mildew of my camper pretty well also.
Another great product is the POR-15 Marine Clean works a little better then
the purple power but cost more.
These are all in the same catagory as Simple Green all good strong
environmentally friendly (if you care about that sort of thing) products.
Except the gunk it smells a lot like kerosene, anothe great cleaning agent
for soaking crusty grungy parts, i would not recomment spraying it on an
engine though.

Scott
1956 Dodge Custom Royal Lancer
2002 Dodge Ram Quad Cab





----Original Message Follows----
From: "Bill K." <pontiac@xxxxxxxxxxxxxx>
Reply-To: "Bill K." <pontiac@xxxxxxxxxxxxxx>
To: L-FORWARDLOOK@xxxxxxxxxxxxx
Subject: Re: [FWDLK] Degreaser
Date: Thu, 29 Jul 2004 02:30:11 -0400

Speaking of which, can anyone recommend a good degreaser, maybe something
that will loosen it up so I can knock it off with a hose?

I'm trying to track down a pretty bad oil leak in a car and oil is all over
everywhere on this thing, I've changed the most obvious sources and still
leaks like mad - like a quart in 100 miles.  Might be the rear main seal,
but I need to clean it up enough to spot a fresh trail without expending a
ton of effort -


Now if it also happens to work well on old, grime-encrusted Forward Look
parts, so much the better.



Bill K.



----- Original Message -----
From: "David Homstad" <dhomstad@xxxxxxxxxxx>
To: <L-FORWARDLOOK@xxxxxxxxxxxxx>
Sent: Thursday, July 29, 2004 1:38 AM
Subject: Re: [FWDLK] P/S & MOAN


> Neil,
>
> You are supposed to keep the lid on the reservoir when washing the
engine.
>
> I would stick the return hose in a bucket and run the engine to flush out
> the old stuff. Keep adding ATF while flushing until it looks clean. Turn
the
> wheel a half turn left and right to send fresh fluid through the various
> passages in the steering box. When the exiting fluid looks clean, let the
> reservoir run dry and shut off the engine. Wipe the reservoir out with a
> clean cloth if you can, then refill and run again.
>
> If it appears that a slime is still stuck to the walls of the reservoir
> after flushing, it may be coating the entire system. Try flushing again
with
> ATF mixed with alcohol, about 2 parts ATF and 1 part alcohol. Use an
alcohol
> that is pure, less that 1% water. I would use Isopropyl alcohol, usually
> found at your local drug store. Alcohol dissolves both water and oil, so
it
> should take care of the sludge. This is the same stuff used in fuel line
> deicers and doesn't affect rubber seals in the fuel pump. It should be
safe
> for recirculating a couple of minutes through the whole system, before
> flushing again. Check the system for sludge after your next cruise.
>
> Dave Homstad
> 56 Dodge D500
>
> -----Original Message-----
> From: Forward Look Mopar Discussion List
> [mailto:L-FORWARDLOOK@xxxxxxxxxxxxx]On Behalf Of eastern sierra Adj
Services
> Sent: Wednesday, July 28, 2004 11:45 PM
> To: L-FORWARDLOOK@xxxxxxxxxxxxx
> Subject: [FWDLK] P/S & MOAN
>
> Well, tonite I was starting to  detail Horrie's engine compartment , &
> used the crummy K-Mart stuff (it foams-up OK, but you gotta scrub the
> stuff, to remove grunge; as opposed
> to the other stuff I've used, that sprays-on as a liquid, & which
> "dissolves"  the grunge, as it 'hits' it--the K-crap didn't even remove
> (all of) the grease, that I had got on my hands; I got the bright idea
> to try it as a hand-cleaner, too--VERY gentle stuff, but.....
> what apparently happened is that I got de-greaser &/or agua into the
> power steering
> resevoir--took H. for a 'cruise', & the P/S pump
> was loudly-groaning (or, was 'that': GROWLING!); got back home &
> discovered that I  now had  "cafe' au lait"  circulating  around the P/S
> system, instead of "thick-cherry-juice"
> ( H.D. P/S fluid )!
>
> Sooo, what is the protocol, now, about getting rid of the franken-fluid
> that's in there, now?
> Can I disconnect the return line, to the resevoir,
> and 'collect' the run-off, while I keep applying new fluid-----can I
> install/use  ATF, to flush-
> out the  "stuff", as there may be a LOT of contaminated-fluid in  the
> system?
>
> Then, when the 'return' fluid starts to look RED
> (using the ATF;  I'm pretty sure that I can just keep the ATF in there),
> do I just install H.D.
> P/S fluid, to top-off the resevoir?
>
> I like coffee, but NOT in the P/S system!!
>
> Neil Vedder
>


---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.710 / Virus Database: 466 - Release Date: 6/26/2004

_________________________________________________________________
Don?t just search. Find. Check out the new MSN Search!
http://search.msn.click-url.com/go/onm00200636ave/direct/01/