Re: IML: Another 60 gage question

["rob van der Es" <r.vdes@xxxxxxxxxxxxxxx>]

Hi Tom,

How is the new solid state regulator doing in your car?
Did you have to add one or two diodes in the ground path to get an
accurate reading on the dials?

Robert


Op Do, 14 juni, 2007 1:40 pm, schreef Tom Scott:
> Clay...I don't have anymore regulators left.  They sold like hotcakes.
> Here
> is the link for where I purchased them.  You have to buy 4 of them, but
> you'll probably be able to sell them to other people on the list.  They
> are $14 a piece.
> Tom Scott
> 60 Crown Southampton with resurrected gauges
>
>
> http://www.questcomp.com/WebRFQ/ZQuestResults.aspx
> ----- Original Message -----
> From: "Rob van der Es" <r.vdes@xxxxxxxxxxxxxxx>
> To: <mailing-list@xxxxxxxxxxxxxxxx>
> Sent: Thursday, June 14, 2007 3:40 AM
> Subject: Re: IML: Another 60 gage question
>
>
>
>> HI Clay,
>>
>>
>> Looks like you have some problems with the voltage limiter here.
>> You can check the temp gauge easily by grounding the wire that is going
>> to the temp sensor in the engine block. The temp gauge should peg then,
>> don't do it too long, otherwise you will fry the gauge !! Be careful.
>>
>> On the otherhand, I am afraid that you already have fried it, since the
>>  oilpressure gauge still pegs and the temp gauge is dead... You see the
>> powersuplly comes from the temp gauge, the voltage limiter is inside
>> this gauge and is feeding all the other gauges in the cluster except for
>> the Amp gauge.
>>
>> I don't understand however how it comes that your gas gauge reads only
>> one quarter with a full tank...
>>
>> You might also check the wire that is going to the oiltemp sensor for
>> grounding.
>>
>> If you have the cluster out you can check the condition of the voltage
>> limiter, if you have a multitester you should read a pulsating voltage
>> of aprr. 5-6 Volts. If your meter shows 12 Volts your regulator is
>> fried, and you are in for a new one.
>>
>> Tom Scott might have another solid state limiter on the shelf !
>>
>>
>> Good luck,
>>
>>
>> Robert
>>
>>
>>
>>
>> Op Do, 14 juni, 2007 2:20 am, schreef Clay Smith:
>>
>>> Greetings everyone
>>> I think the gages are fried in my 60 .
>>>
>>>
>>>
>>> The temp gage is dead. The oil pressure gage will peg and stay there.
>>>  The
>>> gas gage will rise to a quarter a tank and stay there.(with a full
>>> tank). The amp gage is fine but I read in the archives that it isn't
>>> effected by the failing voltage limiter. My question is this  Will
>>> installing the limiter now make the gas and oil pressure gages read
>>> normal again?.Or are they probably toasted ?
>>>
>>> Thanks
>>> Clay Smith
>>> 60 Custom
>>> 67 Crown Coupe
>>> .
>>>
>>>
>>>
>>>
>>>
>>>
>>> -----------------  http://www.imperialclub.com  -----------------
>>> This message was sent to you by the Imperial Mailing List. Please
>>> reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
>>> shared with everyone. Private messages (and attachments) for the
>>> Administrators
>>> should be sent to webmaster@xxxxxxxxxxxxxxxx To UN-SUBSCRIBE, go to
>>> http://imperialclub.com/unsubscribe.htm
>>>
>>>
>>>
>>>
>>
>>
>>
>>
>> -----------------  http://www.imperialclub.com  -----------------
>> This message was sent to you by the Imperial Mailing List. Please
>> reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared
>> with everyone. Private messages (and attachments) for the Administrators
>> should be sent to webmaster@xxxxxxxxxxxxxxxx To UN-SUBSCRIBE, go to
>> http://imperialclub.com/unsubscribe.htm
>>
>
>
> -----------------  http://www.imperialclub.com  -----------------
> This message was sent to you by the Imperial Mailing List. Please
> reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared
> with everyone. Private messages (and attachments) for the Administrators
> should be sent to webmaster@xxxxxxxxxxxxxxxx To UN-SUBSCRIBE, go to
> http://imperialclub.com/unsubscribe.htm
>
>
>




-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please 
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be 
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm