|
The first year for mandatory 4 - way flashers was 1966, as
far as I can recall. (Backup lights, too.)
If Imperial had them in 1960, even as an option, I'm
astonished!
I learn something new every day, here!
Dick Benjamin
----- Original Message -----
Sent: Friday, February 02, 2007 6:18
PM
Subject: Re: IML: 1961 imperial no brake
lights
I don't know for sure about the '61s but 4-way
flashers were an option on the 60 Imperial and all other Chrysler products of
that year. I believe a 61 Imperial I had once had them as well, but
won't bet the ranch on it.
As far as what was where in the wiring, I have no
idea.
Jim in OR
----- Original Message -----
Sent: Friday, February 02, 2007 5:13
PM
Subject: Re: IML: 1961 imperial no
brake lights
THAT is decidedly wierd! Has someone modified
your car? There should not be another flasher on the car unless someone
has retrofitted it with emergency flashers (4-ways).
Regarding the various suggestions involving the
parking light sockets etc. - there is no connection between the brake lights
and the parking lights - they are on totally different circuits - at least
they are SUPPOSED to be!
Electrical circuits can do strange things sometimes,
especially when the car is old enough to develop spurious electrical paths
that are not designed into the car, due to corrosion etc., so I cannot say
for certain that a bad ground on a parking light socket can cause brake
lights to fail - but I'd have to see a schematic of THAT circuit to
convince me.
Dick
----- Original Message -----
Sent: Friday, February 02, 2007 11:05
AM
Subject: Re: IML: 1961 imperial no
brake lights
ok Ill try that but you dont think it has anything to do
with the flasher cause my blinkers work whether the flasher unit is
plugged in or not ?
Dick Benjamin <DickB@xxxxxxxxx> wrote:
This situation comes up about 6 times a year on
the IML - you can find many discussions in the archive... Most
likely, the failure is in your turn signal switch.
If you study the wiring diagram in the FSM, you
can see where to probe with your meter or test light to prove this to
yourself.
The 12 volts from the brake light switch is routed
through the turn signal switch to direct it to the rear light sockets,
because the turn signals share the same filaments in the bulbs - the
brake light current has to be interrupted by the turn signal switch when
you are signalling for a turn at the same time you are stepping on the
brakes.
When the turn signal switch becomes worn, it
usually starts to interrupt the brake light signal even when you are NOT
signalling for a turn.
Sometimes, you can make the problem go
away (momentarily) by wiggling the turn signal switch. Have
someone stand behind the car (or back up to a wall where you can see the
red glow) and wiggle the TS switch while you press on the
brake pedal - you may be able to find a position of the handle
where the brake lights work - if this is the case, start searching
for a replacement turn signal switch.
Dick Benjamin
----- Original Message -----
Sent: Friday, February 02, 2007
2:33 AM
Subject: IML: 1961 imperial no
brake lights
Can someone give me some advise. Got no brake
lights. I checked the power going to the switch its good . I put
in a new switch its the kind that is in line with the fluid. No brake
lights. Now could it be the bulbs cause the blinkers and tail
lights work there all in one ? I don't think so There is something
weird going on though. When I start the car It starts with tail lights
on . Even though the light switch is off. But there not on solid
they pulsate. To make this all go away all I have to do is turn the
blinkers on and off and the tail light go off . Isn't
that strange. Anyone have any advise ?
|
Back to the Home of the Forward Look Network