|
 55/56 dodge idler arm identificationJump to page : 1 Now viewing page 1 [50 messages per page] | View previous thread :: View next thread |
| Forward Look Technical Discussions -> Steering and Suspension | Message format |
hondaman1974 |
| ||
Veteran Posts: 235   Location: Northern Illinois | |||
| |||
| hondaman1974 |
| ||
Veteran Posts: 235 Location: Northern Illinois | . (IMG_4075.JPG) Attachments ----------------  IMG_4075.JPG (244KB - 167 downloads) | ||
| |||
| hondaman1974 |
| ||
Veteran Posts: 235 Location: Northern Illinois | . (IMG_4074.JPG) Attachments ---------------- IMG_4074.JPG (214KB - 156 downloads) | ||
| |||
| hondaman1974 |
| ||
Veteran Posts: 235 Location: Northern Illinois | . (IMG_4073.JPG) Attachments ---------------- IMG_4073.JPG (237KB - 174 downloads) | ||
| |||
| 56D500boy |
| ||
Exner Expert 10K+ Posts: 10797   Location: Lower Mainland BC | hondaman1974 - 2025-07-06 9:26 AM i dont think its a moog k255 as it uses the threaded sleeves and roller bearing/ washer. this was on a 56 dodge coronet that was a parts car. it is now on my 55 dodge and really tightened up the suspension slop caused by the idler arm. would like to find another for my 56 custom royal. thanks! Tony: The OE PN for the bare idler arm is 1611 209 for 55-56 Plymouths and Dodges. That does not include the threaded bushings. I think bushing PN is 1634544. I can find the bare idler arms but not the separate bushings. What I can find is idler arms and bushings as a set. Bernbaum supposedly has a complete idler arm unit (with bushings): https://www.oldmoparts.com/front-axle/idler-arm-d-180 I previously investigated alternative sources of 55-56 Dodge/Plymouth V8 idler arms (the sixes didn't use one) and found old kits from Elgin and Moog. The Moog kit was a K-149. I did find one ball bearing kit but it was for the senior cars so I don't know if it would fit on a 55-56 Dodge: https://www.ebay.ca/itm/145719845118 Searching just now for a 1956 Dodge Moog K-149 turned up a kit with a decent price: https://www.pre60s.com/product/idler-arm-dodge-plymouth-1955-1956-2/  My previous investigations: http://www.forwardlook.net/forums/forums/thread-view.asp?tid=79083 Edited by 56D500boy 2025-07-06 3:11 PM | ||
| |||
| Powerflite |
| ||
Exner Expert 10K+ Posts: 10397 Location: So. Cal | |||
| |||
| 56D500boy |
| ||
Exner Expert 10K+ Posts: 10797 Location: Lower Mainland BC | Powerflite - 2025-07-06 11:27 AM Those ball bearing kits were a common aftermarket upgrade for these cars. They occasionally pop up on Ebay. At some point (probably in 2017) I found an aftermarket kit that improved the situation with the idler arm in my 56 Dodge. Shown here incidentally as part of an exhaust thread that I started. I see bearings and somekind of retainer bar (??). It's worked thats all I can say. | ||
| |||
| hondaman1974 |
| ||
Veteran Posts: 235 Location: Northern Illinois | |||
| |||
| hondaman1974 |
| ||
Veteran Posts: 235 Location: Northern Illinois | |||
| |||
| 56D500boy |
| ||
Exner Expert 10K+ Posts: 10797 Location: Lower Mainland BC | hondaman1974 - 2025-07-12 9:15 AM anybody know of a good brand of idler arm bearing kit with part numbers for 55/56 dodge? ive been searching and can only come up with kits for desoto/chrysler. In searching for 55/56 Dodge kits, I found those ones for Chrysler and Desotos. I also found one for a 57-58 Buick by "Andrew" (same brand as some of the Chrylser/Desoto kits) So I searched "Andrew Parts Ball Bearing Idler Arm Kits listing" and that resulted in this group, including Andrew Kits and CMC kits (which might be from the same source): https://www.ebay.com/sch/i.html?_nkw=Andrew+Parts+Ball+Bearing+Idler...   Edited by 56D500boy 2025-07-12 3:06 PM | ||
| |||
| Jump to page : 1 Now viewing page 1 [50 messages per page] |
| Search this forum Printer friendly version E-mail a link to this thread |
| (Delete all cookies set by this site) | |
