|
|
Elite Veteran
Posts: 943
  
| Parting out a rusty 1958 Desoto Firedome 4dr ht. No front bumper, I used that on my own car. PM or reply with needs. I'll try to post up a few pics. |
|
| |
|
Regular
Posts: 86
Location: MN | Hi, I'm looking for a '58 Desoto air cleaner like the one pictured below. Please note, I do not own this photo and found it on the web. Thanks, Shawn
 ('58 Desoto Air Cleaner.jpg)
Attachments
----------------
 '58 Desoto Air Cleaner.jpg (103KB - 665 downloads)
|
|
| |
|
Elite Veteran
Posts: 943
| I think I got a base but no lid. I'll check |
|
| |
|
Regular
Posts: 86
Location: MN | Sounds good. Thanks! |
|
| |
|
Extreme Veteran
Posts: 501
Location: Upper East Tennessee | I have a friend looking for the upper and lower stainless steel door moldings for the front and rear passenger side doors. Are these available?
|
|
| |
|
Elite Veteran
Posts: 943
| No luck on the air cleaner base. |
|
| |
|
Regular
Posts: 86
Location: MN | Thanks for checking on the air cleaner. |
|
| |
|
Expert
Posts: 1728
Location: Fleetwood, Pa | Any side trim still available?
|
|
| |
|
Elite Veteran
Posts: 943
| Yes, all 4 pieces of quarter trim. Also I think I still have both pieces of DR rear door trim and 1 or 2 other pieces of the lower door trim. Let me know what you need |
|
| |
|
Member
Posts: 22
| Any cruise control parts? |
|
| |
|
Expert
Posts: 1267
Location: San Antonio TX | Any pics? I'm looking for various pieces of exterior sheet metal for my 58 Desoto. |
|
| |
|
Elite Veteran
Posts: 943
| Cruise? I might have some pieces from 59 and up Imperials. I don't even think cruise control was optional on '58 Desotos. I have the doors from this car, that is about it, anything else that was any good I am saving for my own '58 Desoto. I also have some 57 Chrysler fenders. |
|
| |
|
Expert
Posts: 1267
Location: San Antonio TX | Oh ok. Yeah I'm looking for roof and headlight metal for mine. Those Chrysler fenders might work, since all I need is the metal for the lights. Any pics of the fenders? |
|
| |
|
New User
Posts: 1
| Any chance you have the factory original trunk floor mat with the raised Desoto letters? Thanks |
|
| |
|
Elite Veteran
Posts: 943
| I have the mat in pieces.... |
|
| |
|
Elite Veteran
Posts: 943
| Bump still have parts left from this car
|
|
| |
|
Exner Expert 10K+
Posts: 10033
Location: So. Cal | I need the upper left front fender trim if you have it. |
|
| |
|
Regular
Posts: 85
| steering wheel, possibly windshield? |
|
| |
|
Member
Posts: 22
| Hi, thanks for responding....YES, I am wanting to buy 1958,59 Chrysler/Imperial AP (cruise Control) parts ie: How about the steering column with controller?
What do you have? Can you send me some photos?
Thanks,
Gary my e-mail is: pins.thorne@gmail.com |
|
| |
|
Veteran
Posts: 151
| Do you have the auto trans torqueflite flywheel dust cover ? |
|
| |
|
Elite Veteran
Posts: 1018
Location: Milwaukee Wisconsin | did the car have power brakes ? if so, wanting booster , linkage to brake pedal , vac reserve tank for 59 dodge converting to pb. |
|
| |
|
Elite Veteran
Posts: 717
Location: Finland | I need the rear window interior garnish trim to a firedome 2-d. I think they are the same on 2-d and 4-d hardtop. |
|
| |
|
Exner Expert 10K+
Posts: 10033
Location: So. Cal | The '58 Firedome coupe never came with the rear window garrish trim. That's why yours is missing, Ralf. I'm pretty sure the 4dr trim is different. |
|
| |
|
Member
Posts: 9
| Do you have power steering parts?
Jarmo
Edited by finmopars 2020-01-01 4:34 PM
|
|
| |
|
Elite Veteran
Posts: 943
| Sorry I didn't reply to those who asked about parts. It was a power steering car I have the steering column and I'm almost positive I have the power steering gearbox. No windshield |
|
| |
|
Elite Veteran
Posts: 943
| Steering wheel I have but is the "plain" not the deluxe one |
|
| |
|
Veteran
Posts: 122
Location: Murray Bridge, South Australia | How did you go with the air cleaner base? Previous owner got to mine with a grinder and messed it up badly.
Bob |
|
| |
|
Elite Veteran
Posts: 943
| Sorry I never checked but from this photo here what I have looks different based on my memory (been a while since I looked at it) I'm not sure it's the right one though |
|
| |
|
Member
Posts: 6
| Hi mate would you happen to have the steering column to dash brackets? I need for dodge but im sure they should be similar or the same cheers,
Mike |
|
| |
|
Elite Veteran
Posts: 943
| I'm almost positive I still have those if you still need them. |
|
| |
|
Veteran
Posts: 145
| Would your car have this dome lamp over the glove box? I would like to find one that doesn't need to be re-chromed.
Edited by NM Desoto 2021-08-14 4:21 PM
 (dome light 001.JPG)
Attachments
----------------
dome light 001.JPG (64KB - 266 downloads)
|
|
| |
|
Exner Expert 10K+
Posts: 10033
Location: So. Cal | You could clean that chrome up really well to the point that you wouldn't notice it. |
|
| |
|
Veteran
Posts: 145
|
The rust has etched pretty deep into the steel, the pits are worse than they appear in the picture. |
|
| |
|
Elite Veteran
Posts: 943
| Those are prone to that kind of rust, all I have is ones that need replating, not sure you'll find on that doesn't after 60+ years |
|
| |
|
Exner Expert 10K+
Posts: 10033
Location: So. Cal | Do you have the rear bumper from this car? I am in need of one. It must also have the mounting brackets with it. I didn't want to pay to ship one, but it looks like I have no choice. |
|
| |
|
Elite Veteran
Posts: 943
| Sorry but no I sold the rear bumper a while ago |
|
| |
Parting out 1958 Desoto Firedome 4dr ht
