The Forward Look Network | ||
| ||
I need a 1959-1961 413 Jump to page : 1 Now viewing page 1 [50 messages per page] | View previous thread :: View next thread |
Forward Look Technical Discussions -> Engine, Exhaust, Fuel and Ignition | Message format |
LouisHarper |
| ||
Member Posts: 37 | My 1961 Imperial's motor is toast. I took the cylinder heads off and one cylinder in each bank had severe corrosion. I need a short block (crank, rods, pistons) that only needs bearings, rings, a good honing, and gaskets to be a solid motor. Anything from a 1959-1961 Chrysler or Imperial would work. I am an Auto Restoration student at the college in McPherson, Kansas. Please do not contact me if you are out of state or cannot deliver from out of state. | ||
Fick4fun |
| ||
Veteran Posts: 135 | If a 63 413 will work u can have it it is out of an imperial and was told it ran last year | ||
LouisHarper |
| ||
Member Posts: 37 | Can you check if it spins over and will you send photos, especially pics of the bell housing bolt holes? I would have to switch my crank because the 57-61 trans was different, but other than that everything should be kosher. Where are you located? Edited by LouisHarper 2017-11-21 4:21 PM | ||
Fick4fun |
| ||
Veteran Posts: 135 | I'm located in northern Il and I can check all that for ya tomorrow morn | ||
mstrug |
| ||
Expert 5K+ Posts: 6487 Location: Newark, Texas (Fort Worth) | Opps! He will only take one from KS. He would have to cross Missouri to get it in Ill. Prolly wants it free too. | ||
mstrug |
| ||
Expert 5K+ Posts: 6487 Location: Newark, Texas (Fort Worth) | Here: https://phoenix.craigslist.org/wvl/pts/d/mopar-413-engine/6391322107... https://chattanooga.craigslist.org/cto/d/413-engine-1964-chrysler-ob... https://reno.craigslist.org/pts/d/1959-chrysler-413-engine/638352706... https://seattle.craigslist.org/tac/pts/d/1960-chrysler-imperial-part... https://akroncanton.craigslist.org/pts/d/1965-mopar-dodge-plymouth-4... https://winstonsalem.craigslist.org/pts/d/mopar-413/6346231208.html https://medford.craigslist.org/pts/d/413-mopar-dodge-big-block/63507... https://iowacity.craigslist.org/pts/d/413-mopar-engine/6320370676.ht... https://cleveland.craigslist.org/pts/d/mopar-big-block-passenger-car... Edited by mstrug 2017-11-21 5:40 PM | ||
Fick4fun |
| ||
Veteran Posts: 135 | It was free not looking for money it's just going to sit around might as well let it go | ||
LouisHarper |
| ||
Member Posts: 37 | Wow, thanks for the great deal. Are you planning on a doing a road trip any time soon, because I have no way of getting a motor home from Illinois any time soon. Maybe freight won't be more than $100 and crating it to Kansas would be easiest. Does it have a carburetor with it? | ||
LouisHarper |
| ||
Member Posts: 37 | Are you closer to Chicago or Springfield, and is it would it be quicker to drive through Des Moines or St. Louis to get there? If driving out there is cheaper than freight, I might do that. | ||
Fick4fun |
| ||
Veteran Posts: 135 | It's a whole motor non a.c. car I'll c if I can get pic up for you | ||
LouisHarper |
| ||
Member Posts: 37 | Sounds great. | ||
LouisHarper |
| ||
Member Posts: 37 | What other Forward Look cars do you have? | ||
Fick4fun |
| ||
Veteran Posts: 135 | I only have a 63 imperial | ||
LouisHarper |
| ||
Member Posts: 37 | Did the motor come out of your car or another '63 Imperial? Send photos of both! | ||
Fick4fun |
| ||
Veteran Posts: 135 | The motor is out of a parts car my car is on here some where. | ||
LouisHarper |
| ||
Member Posts: 37 | Did you take photos of the motor yet? A friend and I were thinking about driving out there, but that would be a lot of gas so I'm going to look into freighting it to McPherson. Do you live near a Fastenall? I think that will be the most economical option. | ||
LouisHarper |
| ||
Member Posts: 37 | Is the transmission in that parts car any good? | ||
LouisHarper |
| ||
Member Posts: 37 | Do you have the means to make a crate for the 413 or at least package it nicely on a pallet? I'm looking around for shipping quotes and I also need your town's name for the pickup location on the quote forms. | ||
Fick4fun |
| ||
Veteran Posts: 135 | I can put it on a pallet and the town is springgrove Il I'll get u some pics with the holiday it's been rough | ||
Fick4fun |
| ||
Veteran Posts: 135 | Ya there is a fasenall the store buy me the trans I have no clue about | ||
LouisHarper |
| ||
Member Posts: 37 | One of my classmates at school lives in Westfield, Wisconsin. His mom is driving down with a trailer to pick up he and one of his cars to drive him home for Christmas break, so she might be able to pick it up for me. I'll ask for a shipping quote from fastenal; if you can, make a crate so they will insure against any damages. Open pallets aren't covered by their shipping insurance. Do you have any need for the transmission? | ||
rkandii |
| ||
Member Posts: 25 | Can it be sleeved? I did that to save my KD500 block. | ||
Jump to page : 1 Now viewing page 1 [50 messages per page] |
Search this forum Printer friendly version E-mail a link to this thread |
(Delete all cookies set by this site) | |