The Forward Look Network | ||
| ||
Parting over 40 FL cars Jump to page : < 1 2 3 4 5 6 7 ... > Now viewing page 2 [50 messages per page] | View previous thread :: View next thread |
Forward Look Swap Meet -> Parts Cars - VEHICLES BEING PARTED OUT | Message format |
Bug |
| ||
Member Posts: 11 | Hi, I am looking for some trim pieces for a 57 Dodge Custom Royal. Do you have any of the following; round taillight bezels custom royal script for front fenders headlight trim as well as the small piece that joins the headlight trim at the top/centre of the headlight emblems for the rear fenders as well as the emblem on the trunk Thanks | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | I have a Coronet 2-door sedan that has one pit-free taillight bezel, and two others with just light pitting, no blistering. The stainless over the headlights has a couple of small dents, but not crushed or creased. The center joining trim is in poor condition, not worth repairing. If you still need these items, PM me. ---John | ||
RoyalGate |
| ||
Expert Posts: 2011 Location: Ballwin, Missouri | John, I am looking for a three speed shift cable for a Plymouth or Dodge, roughly '58 or '59. I am changing my '59 Coronet over to a three speed and need a serviceable cable. Thanks, Larry | ||
TAlex |
| ||
Member Posts: 24 Location: Warren, Michigan | Hi, I am looking for the Jiffy Jet washer bag mounting brackets for a '58 Plymouth. I think that all '57-'58s have common brackets but I'm not sure. I also need the check valve for the washer system. Thanks! Todd | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Larry, I was always under the impression that the 3 and 2 speed cables were the same, although the shift quadrant is different. I'll see if i have the distinct 3-speed unit still in a car and let you know. And Todd, I know for a fact there are a few cars out here that still hold their washer bag brackets, not sure on the valve though. ---John | ||
TAlex |
| ||
Member Posts: 24 Location: Warren, Michigan | Thanks John. I sent you a PM about the brackets. -Todd | ||
chipplake1 |
| ||
Veteran Posts: 143 Location: Chippewa Lake, OH | Hi, I am looking for a propeller shaft with both u-joints for a 1957 Chrysler 2-door. Thanks, Steve | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Hi Steve, what transmission does your car have? Please let me know and I will check for you. ---John | ||
chipplake1 |
| ||
Veteran Posts: 143 Location: Chippewa Lake, OH | Hi John, My car is a push button automatic. Thanks! Steve | ||
oldefar |
| ||
Elite Veteran Posts: 708 Location: Fredrikstad, Norway. (Europe) | Hi big m! I need the complete front clip for 1961 PLYMOUT, all models 2 and 4 door fit: LEFT & RIGHT FRONT FENDERS MOST IMPORTANT but also hood and grille. Surface rust (NO rust holes) and small dings OK. PLESE HELP. You can't amagine how hard it is to find parts at a reasonable price over here. Best Regards from Einar in Norway. P.S. I will of course pay all expences connected to shipping. THANKS. | ||
matador440 |
| ||
Elite Veteran Posts: 690 Location: BELTSVILLE, MARYLAND 20705 | I ALSO HAVE A FRONT CLIP FOR A 61 PLYMOUTH IF BIG M DOESNT HAVE ONE. EAST COAST OF USA...... PARTS CAN GO OUT OF BALTIMORE THANKS SMITTY | ||
60 Finatic |
| ||
Extreme Veteran Posts: 481 Location: near St Augustine, FL | John, I have a 60 Fireflite 2 dr hardtop. I am looking for a few things: - the clips for the stainless trim that goes around the base of the windshield and the rear windows - clips that hold in the weatherstripping for the windshield & rear window - the rubber molded piece held in with two screws that goes on the frame/roof juncture behind the front, top edge of the vent frame on both the driver and passenger sides (I know that one is hard to picture...) - the rubber molded piece that goes in the front of the quarter panel behind the front door that seals the rear window track when the window is closed for both the driver and passenger sides (I know, another hard one to picture). - two horns - jack and stand The rubber doesn't have to be perfect, just enough that I can make it operational. Thanks in advance! Dan Edited by 60 Finatic 2006-06-06 11:24 PM | ||
mkmskm |
| ||
Member Posts: 7 | I'm looking for an A/C clutch from a '56-60 Mopar that is the 7/5" external brush type. Summer gets hot here Malcolm | ||
john59oldcar |
| ||
Member Posts: 26 Location: Spring Grove, IL. | I am looking for a rear seat for my 56 Plymouth convertible. I believe 55-56 Dodge and Plymouth were the same. Thanks, john59oldcar@yahoo.com | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Sorry, but I do not have that convertible rear seat. ---John | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Recent Mopar acquisitions: '56 DeSoto Firedome 4-door sedan '56 Dodge Coronet 4-door sedan '57 Dodge Coronet 4-door sedan '58 Dodge Coronet 4-door sedan '59 Dodge Coronet 4-door sedan 5 '57 Plymouths, 3 4-door sedans, 1- 2-door sedan, and one 4-door hardtop '59 Plymouth Suburban wagon '60 Plymouth Fury 2-door HT '57 Imperial 4-door HT '62 Imperial 4-door HT '56 Chrysler New Yorker 4-door sedan '57 Chrysler Saratoga 2-door HT '58 Chrysler New Yorker 4-door HT '58 Chrysler Windsor 2-door HT, nice rust free car, complete '59 Chrysler Saratoga 4-door sedan '62 Chrysler 2-door HT All these cars are for parts, except for the '58 Windsor, which will be for sale complete. Please let me know if there are items that you need. ---John | ||
5859 |
| ||
Expert Posts: 2932 Location: Lemoore CA | John, do you have a good hood for my 59 Dodge Coronet 2 door hardtop? by good I mean minimal dings, and no rust out on the skin or braces, a little surface rust is OK. Also looking for good front fenders. thanks | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Hi James, The '59 I recently picked up was left out in the redwoods for years, and the forest debris caused rust through on the hood. I believe the left fender was good and solid, the right fender had a large dent above the wheelwell where a tree had grown against it. I'll get back to you with a better description after I check it out. ---John | ||
Kenny J. |
| ||
Inactive by user's request Location: Las Vegas, Nevada | As usual, I must ask...any V-8/stick '57-'59 cars in this bunch? K. Edited by Kenny J. 2006-07-02 3:40 PM | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Kenny, the '59 Suburban is equipped with a V8 and three speed, but not overdrive. ---John | ||
Kenny J. |
| ||
Inactive by user's request Location: Las Vegas, Nevada | I have an overdrive, John...but I can use everything on you wagon for a V-8 stick set up (flywheel, clutch assembly for core purposes or rebuilding, starter, bellhousing tranny, shifter from column, all shifter linkage, shifter & clutch rods, swivels, z-bar etc. Since I'm putting an eight in the blue wagon, I could use the little "V" emblems for the rear quarters and tailgate. I am assuming it's a 318 wagon... Please e-mail me. Also found some more side trim hidden in the pink wagon and need to revise which trim pieces I need. I sold some Ch*vy stuff (FINALLY) and may as well use the money for this stuff. K. P.S.- Ray Bell needs an overdrive, if you ever come across any. I have two that are only good for parts and one in the pink wagon. But my black wagon has a straight three speed without overdrive and that's why I am interested in what you have. | ||
KRUZIN55 |
| ||
Member Posts: 22 Location: New Hampshire | Looking for 55 Belevedere Right Front Fender Script and Center Chrome trim peice on the hood | ||
5859 |
| ||
Expert Posts: 2932 Location: Lemoore CA | John, I think I will keep looking, hopefully I Can find the hood and fenders in one place. I just wanted to say thankyou on those other parts you sold me, so far I have had good luck with them, the carb, I just opened it up, sprayed it out with carb cleaner, put it back together and installed it, runs great, I didn't even have to adjust it, the accelerator pump is weak, which I will adress when I rebuild it, but I couldn't be happier with it. I may be back in touch with you on the one fender if I can't find one, both of mine are fair, but if given the choice I would rather replace them with ones that have no rust out than repair them. | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Thanks for letting me know on the carb, James. I am supposed to be getting another '59 4-door sedan in, as well as a 2-door hardtop body shell. I will certainly keep you in mind if the front sheetmetal looks good. ---John | ||
72sst |
| ||
Extreme Veteran Posts: 327 Location: Orefield,Pennsylvania | John, How do you find all these neat Plymouths? Eric | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Hi Eric, most of these cars I find by word of mouth, from other salvage operators or friends. A few have been bought from e-bay or craigslist, and I still find some through local newspapers. I used to drive in some demo derbies, so I know a lot of the guys that still do, and I find '76 Caprices and put them up for trade, if they find finned cars. These guys have way more time on their hands than I do so it works out well. Farm and ranch auctions and property clean-ups are some other prosperous ways to locate and buy cars. ---John | ||
KRUZIN55 |
| ||
Member Posts: 22 Location: New Hampshire | I am looking for 12 volt Guages for my 55 plymouth Belevedere, Fuel, Amp, temp, I believe the 56 was the same, don't know if any others will work. Also looking for L/R Chrome Spear above the rear tire. Edited by KRUZIN55 2006-07-23 8:25 AM | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | The only '56 I currently have, unfortunately had an engine fire that went under the dash as well. If I get a '55 or '56 in, I will let you know. ---John | ||
59 SportSub |
| ||
Member Posts: 32 Location: Whitewater, Ca | Hey, I see you just got in a '59 Suburban. How is the tailgate? I need one. Dave | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Hi Dave, I actually have four '59 wagons for parts. I believe the one has a nice tailgate, I'll check it out and let you know. ---John | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | The best tailgate has no rust out, but it appears there is some bondo towards the right lower. I removed the interior cover panel, and cannot see the usual signs of damage, such as holes drilled or wavy, distorted metal. Most likely this filler isn't thick. The price for the tailgate shell is 200.00. Please contact me if you are interested. ---John | ||
alwndup |
| ||
Veteran Posts: 260 Location: SLC, UT | As for the 61 Dodge sedans, could one of them be a Polara? I need a few pieces of trim. Thanks in advance, Mont | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Hi Mont, just picked up a loaded '61 Polara. Check your e-mails. ---John | ||
john59oldcar |
| ||
Member Posts: 26 Location: Spring Grove, IL. | I need a good door latch assembly for my 59 Plymouth Sport Fury. Do you have one for the drivers door that isn't worn round on the rotating latch. Thanks, John john59oldcar@yahoo.com | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | I'm just about positive that I can come up with a good one. I've got Jury duty today so I will e-mail you back tomorrow morning to let you know. ---John | ||
bilspasser |
| ||
Regular Posts: 91 Location: Naestved, DK-Denmark | Hey. I´m in a big need for a gas tank for my 1957 FL car, and I could shure use a new windshield, as mine is broken in several places.(2dr hardtop). -Could you PLEASE help me out here ! Stig Hansen,Denmark (1957 Dodge Regent , equals Savoy with a dodge front clip) | ||
TAlex |
| ||
Member Posts: 24 Location: Warren, Michigan | Hi John, You wouldn't happen to have a restorable set of the front swivel seats ('59-??) would you? I'm thinking about replacing the bench seat in my '58 with the swivels. This is on the "wish" list as opposed to the "need" list, I'm just curious about how available they are and how much they go for. Thanks, Todd | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Hi Todd, I get these in occasionally, but do not have any currently. The interesting thing is that most of them I find have been installed in non-Chrysler cars in the past. I get 5-600.00 for seats in good operating condition, and up to 800.00 for the power versions. Hope this info helps, John | ||
matador440 |
| ||
Elite Veteran Posts: 690 Location: BELTSVILLE, MARYLAND 20705 | TODD, IF YOU FIND THE SEAT I HAVE BEAUTIFULL REPRODUCTION SEAT CABLES IN STAINLESS STEEL. GOOD LUCK -- OH THAT REMINDS ME I KNOW WERE AS SET IS IN A 59 DODGE ILL GO LOOK AND SEE IF THEY ARE STILL THERE-- KEEP IN TOUCH | ||
TAlex |
| ||
Member Posts: 24 Location: Warren, Michigan | Thanks guys. Please keep me in mind if you come across a usable set. -Todd | ||
5859 |
| ||
Expert Posts: 2932 Location: Lemoore CA | John, would you happen to have any glass for a 62 chrysler Newport 2 door hardtop? I am looking for everything but the vent wings. thanks | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | James, For a 2-door hardtop, I have all but the rear glass. Give me a shout, and we'll get 'er going. ---John | ||
58hemi |
| ||
Member Posts: 19 Location: cheshire. united kingdom | hi john i am looking for a gas tank for my 1958 chrysler 2 door hardtop. could you let me know if you have anything available. thanks david. | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Hi David, all the '57-'59 tanks I have left are dented on the underside. Sometimes the dents can be popped out with water pressure, but you never know until you try. ---John | ||
narleycharlie |
| ||
Expert Posts: 1812 Location: Slidell La. | Hi BigM , I m in need of a 3spd pushbutton assembly for a 59 Ply . I m switching from a 2 to a 3 , my old cable works fine and should be compatable with the 3spd , am I correct on that ? I also need the bezel/trim that surrounds it . Don t know if they had diff styles of trim . Thanks NC | ||
58 freak |
| ||
Veteran Posts: 200 Location: australia | i need one little molding, just below the drivers side rear tail light, for a 58 plymouth. If you have a good one pls P.M me thanks! | ||
1958Paul |
| ||
Veteran Posts: 166 Location: Nebraska | Good stuff here - I can vouch 1st hand!! | ||
carjock |
| ||
Account Inactive by Request Posts: 1601 | John: I am converting a '59 Coronet 2-door sedan with the stock 326 and powerflite trans over to a "super D500" with torqueflite trans. What I need is a COMPLETE set of engine mounts for the 383 engine (the part that bolts to the crossmember and the part that bolts to the engine), the rear transmission mount/crossmember (if different for torqueflite trans), the shifter control quadrant and trim plate for the dash and control cable (if unique for torqueflite), any unique throttle land downshift linkage parts for the 383 engine. If one of the coronets that you have has a big block engine (361/383) with torqueflight, those parts would work fine. I also think a lot of Desoto parts interchange. Thanks. Jim | ||
big m |
| ||
Expert 5K+ Posts: 7805 Location: Williams California | Hi Jim, unfortunately, all the Dodges and DeSotos I currently have are equipped with the poly engines. If something should turn up, I will certainly let you know. ---John | ||
bad58mike |
| ||
Elite Veteran Posts: 1150 Location: Southern California | Big M, I was referred to you by other members on this forum and I'm in great need of a nice set of hood hinges for my 58 plymouth, I was out this wekkend cruisin to a local show when the hood flew up on the highway due to a damged hood clip and damaged the top side of my fenders and rear hood and due to this occuance the hood hinges are shot she will go to the body shop soon for repair but I'm almost sure they will need a set of hood hinges. Please let me know if you can help. I can also be reached At my office email which is mheredia@hra.com. My cell is (949) 533-6904. oh and if you have another hood latch to that would be great Thanks. bad58mike | ||
Jump to page : < 1 2 3 4 5 6 7 ... > Now viewing page 2 [50 messages per page] |
Search this forum Printer friendly version E-mail a link to this thread |
(Delete all cookies set by this site) | |