|
|
Location: The Mile High City | The prototypes went pretty well for an initial effort, but there are a lot of refinements to be done! The 3-D printing process is amazing, but I need a much sharper print. Painting is the easiest part, but I think I need to incorporate metallic foil to make it better. The thick urethane coat was a bubbly, uneven failure. I need a better substitue, maybe a resin.
(Prototype 3 reduced.jpg)
(Prototype 4 reduced.jpg)
(Prototype 5 reduced.jpg)
(Prototype 6 reduced.jpg)
Attachments ---------------- Prototype 3 reduced.jpg (246KB - 87 downloads) Prototype 4 reduced.jpg (244KB - 84 downloads) Prototype 5 reduced.jpg (240KB - 84 downloads) Prototype 6 reduced.jpg (231KB - 81 downloads)
|
|
|
|
Location: The Mile High City | Still working on this project. I was able to order a set of the "wheelcover center emblems that never were" from Xometry and they printed in stereolithography with Accrua xtreme grey material - and the quality was pretty good. I think the cost was about $160. Painting them was a bit of a challenge, but I think they are decent enough to replace the Chrysler centers that are in there now. They are not exquisite quality on close inspection, but I think they will be decent from a distance of just a couple of feet away.
(01 first coat red.jpg)
(02 second coat white and black.jpg)
(03 third coat light gold.jpg)
(04 fourth coat yellow.jpg)
(05 final clear coat.jpg)
Attachments ---------------- 01 first coat red.jpg (85KB - 32 downloads) 02 second coat white and black.jpg (188KB - 32 downloads) 03 third coat light gold.jpg (190KB - 29 downloads) 04 fourth coat yellow.jpg (243KB - 37 downloads) 05 final clear coat.jpg (111KB - 29 downloads)
|
|
|
|
Expert
Posts: 1211
Location: SWITZERLAND | Mike, put the red paint at least, must be quite liquid and flow. Before do paint the emblems somewhat "over" the border. Then the color separation will become very accurate, as I did with some knight emblems when golden coating. And use paint which is not aggressive to the resin. Good Luck! - SERGE -
Edited by sermey 2024-02-09 1:35 PM
|
|
|
|
Location: The Mile High City | Thanks, Serge! Working on the Adventurer emblems now. So far, they have been easier to paint. I started with gold and then masked off the gold to apply the silver background. I tried to mask off the silver and gold to apply the black, but ended up having to hand paint the black with gloss enamel. Still need to apply the clear-coat.
(Adventurer Center Emblems reduced.jpg)
Attachments ---------------- Adventurer Center Emblems reduced.jpg (237KB - 7 downloads)
|
|
|
|
Location: The Mile High City | Final products:
(Custom Center Cap set 02.jpg)
(Stock Set 02.jpg)
(Stock Set 03.jpg)
Attachments ---------------- Custom Center Cap set 02.jpg (250KB - 6 downloads) Stock Set 02.jpg (240KB - 6 downloads) Stock Set 03.jpg (235KB - 4 downloads)
|
|
|
|
Expert 5K+
Posts: 9706
Location: So. Cal | They look quite nice. Which ones are you going to use? |
|
|
|
Location: The Mile High City | Thanks, Nathan! I'm definitely going with the red centers for now. I repainted the '57 wheelcover centers to gold to get a bit closer to the real thing. Not too shabby for "home made" - what do the hipsters call it? Bespoke! |
|
|
|
Expert
Posts: 1211
Location: SWITZERLAND | Lancer Mike - 2024-05-04 7:00 PM Thanks, Serge! Working on the Adventurer emblems now. So far, they have been easier to paint. I started with gold and then masked off the gold to apply the silver background. I tried to mask off the silver and gold to apply the black, but ended up having to hand paint the black with gloss enamel. Still need to apply the clear-coat. Before applying the clear-coat I would do small corrections under the microscope. Small improvements make big effect, as shown. Left Original - right corrected. - SERGE -
Edited by sermey 2024-05-19 6:09 AM
(Adventurer Center Emblems reduced corrected.jpg)
Attachments ---------------- Adventurer Center Emblems reduced corrected.jpg (264KB - 0 downloads)
|
|
|
|
Expert 5K+
Posts: 5011
| looks good, start doing other emblems
|
|
|