RE: timing
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: timing



Not sure what you are getting at with the gasket question.  But in this case, to avoid dropping the oil pan I used Permatex “Right Stuff” in place of the rubber gasket where the timing cover and oil pan meet.  Also works good for end seals on intake manifolds, instead of using the old skool foam seals they give you.  I would never use RTV on an engine – silicon is good for bathroom sink drains etc around the house, and that’s about it..........

 

When you do have a gasket, Permatex anaerobic sealer is the cat's meow........  Or Aviation Sealer....... Or Hylomar.......... 

 

Permatex high temperature thread sealant to seal threads of all sorts – especially bolts that can enter water jacket – Head bolts – Water pump bolts – Timing cover bolts – Intake bolts - Exhaust manifold studs.

 

 

From: Hall, Ricky L
Sent: Thursday, June 22, 2017 7:00 AM
To: '1962to1965mopars@xxxxxxxxxxxxxxxx' <1962to1965mopars@xxxxxxxxxxxxxxxx>
Subject: RE: timing

 

Another war story..........   Had restarted a 472 Cadillac engine out in the driveway in 2012 with 150,000 miles on it several times after sitting 20 years.  Then all the sudden it started backfiring thru the carb, and even about blew up a muffler in a big backfire BOOM!  Towed it around to the garage thinking the timing chain skipped. 

 

Turned out it wasn’t getting any oil in the distributor/timing chain area and the gear on the distributor ground down to dust.  Put on a Cloyes set, updated the distributor to HEI, and drilled a .003 hole in one oil galley plug to get oil to the timing chain and gears.  Problem solved – driving the rig with that engine in it today.  Chevy had a foaming oil issue in oil galleys, and that was GM’s fix, they even had galley plugs with the hole in them.

 

 

From: 1962to1965mopars@xxxxxxxxxxxxxxxx [mailto:1962to1965mopars@xxxxxxxxxxxxxxxx] On Behalf Of dodge440@xxxxxxx
Sent: Thursday, June 22, 2017 6:36 AM
To: 1962-1965 Mopar <1962to1965mopars@xxxxxxxxxxxxxxxx>
Subject: Re: timing

 

Bob,

 

I remember changing head gaskets in my youth and when we cranked the engine we had the same thing happen. I think we had the valves one or more set to tight, valve lash, , 57 F____ Stock Six. We had to check them to see that the push rods were not bent. We then set the valves as loose as possible and then adjust them properly.

 

Just a thought from 50 yrs. or more ago.

 

Jim

 

Coronet 500 440CI

On Jun 22, 2017, at 7:28 AM, carverex@xxxxxxx wrote: 

 

Hi Bob

 

It could be a much simpler fix. Maybe the distributor is 180 deg out? Backfiring through the carb would be a classic indication of that.

 

Good luck

Lyle 

On Thursday, June 22, 2017 at 12:34:16 AM UTC-4, Bob Turner wrote:

I changed cams a while back. I tried to start it up and it backfires through the carb.
 Does it sound like I did not line up the marks on the timing chain right ( 180 ) out ?
 Is there any way to tell besides taking the timing cover back off?
  What would be a good gasket to use?
          Thanks

 

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.

 

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.