Re: 361 Tuning Problem with New Cam, Side Thread to Cab Synchronizers

[Jimmy Peavy <peaver63@xxxxxxxxx>]

Sounds like it's running out of fuel on demand.
Have you changed out the inlet/needle valves and seats?

Jimmy



On 1/16/14, hmsevans@xxxxxxx <hmsevans@xxxxxxx> wrote:
> I joined this thread to seek parts and advice on my 1962 Sport Fury 413
> Project.
> After reading the last thread on Tuning
> I would like to ask if it would be OK to ask for some help solving the
> issues I have on my just completed 1959 Ply Sport Fury with a 1959 361 that
> I had built with a new Cam.
> If not OK ,I would appreciate any input via personal email.
>
> The Problem is Bogging (almost) to  a stall when you want more power at
> 20-40 MPH cruise. It will Run strong off the line if you nail it, Starts and
> idles OK.
> Just unsafe to drive in traffic!
>
> The Motor is a 1959 Plymouth 361 , Bored .060 over , Heads ,Stock Exh. 1.60,
> Intakes was, 1.96 ,now 2.08 ,
> Cam is a Schneider , closely resembles the 1960 Commando cam.
> The cam is set at 109 deg intake CL/111degs ,Exhaust CL with a 110 deg lobe
> spread
> .Intake duration is 270 deg/Exh dur is 290 deg.
>  Intake lift is .440/Exh lift is .460.
> Valve springs are 90-100 lbs.
> Compression Stock, 10-1
>
> Carb is rebuilt Carter Stock AFB - 2856S
> Distributor is Mopar Performance Elec Ignition
> Running 110 Leaded Race Fuel for tests, runs the same on unleaded pump gas
>
> I have the Mopar 2x4 Carb ( Carter # 2652S and 2653S ) setup ready to
> install. But I would like to sort out the Bogging issue before I switch the
> Manifolds.
> Any Ideas
> Mark Evans
>
>
>
> --
> --
> --
> Please address private email -- email of interest to only one person --
> directly to that person. That is, email your parts/car transactions and
> negotiations, as well as other personal messages, only to the intended
> recipient. Do not just press "reply" and send your email to everyone using
> the general '62-'65 Clubhouse public email address. This practice will
> protect your privacy, reduce the total volume of mail and fine-tune the
> content signal to Mopar topic. Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and
> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> --
> You received this message because you are subscribed to the Google Groups
> "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> http://groups.google.com/group/1962to1965mopars?hl=en.
>
> ---
> You received this message because you are subscribed to the Google Groups
> "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
> For more options, visit https://groups.google.com/groups/opt_out.
>

-- 
-- 
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

--- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.