Re: New Drive Shaft
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: New Drive Shaft



Ray,

 

I thought the same thing myself since I've seen this conversion by other companies and the spine was on the front end. When I asked DSI about this they said this design worked best for several reasons. First the spline unit is heavier than the flange unit. By placing the spline at the rear it reduces the weight at the tail shaft. Aluminum tailshafts don't like weight and tend to crack, this being the major reason. Second there is less strain on the tailshaft with the spline taking the movement at the rear with the rearend housing moving up and down with the suspension. This is a Performer Series Driveshaft, 4" OD, I believe rated to 600hp.

 

Nick

 



 


From: "Ray Bell" <raybell46@xxxxxxxxx>
To: 1962to1965mopars@xxxxxxxxxxxxxxxx
Sent: Thursday, August 8, 2013 9:16:54 PM
Subject: Re: New Drive Shaft

Strange that they'd do it that way, I'd have thought the spline would last better up the front end...

Should I need to do this with my Valiant, I'll be modifying a Japanese 4WD driveshaft and putting its spline up the front end.


Ray

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
 
---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
 
---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.
 
 


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.