RE: master cylinder?

["Daniel McCormack" <mcwheels@xxxxxxxxxxxxxx>]

Gary if you're talking about power brakes you don't need the rubber locking
ring but........with manual brakes you stand a good chance of the brake rod
falling out of the back of the master cylinder if the rubber locking ring
isn't installed. 


-----Original Message-----
From: 1962to1965mopars@xxxxxxxxxxxxxxxx
[mailto:1962to1965mopars@xxxxxxxxxxxxxxxx] On Behalf Of Gary Pavlovich
Sent: Monday, April 08, 2013 9:57 PM
To: 1962to1965mopars@xxxxxxxxxxxxxxxx
Subject: Re: master cylinder?

I used the Mopar dual resevoir MC from Master Power Brake on my '56 Plymouth

and an adjustable brake rod from the same vendor - no issues as these pieces

interchange for many, many years.

I removed the rubber "piece" on the brake rod as you cannot set the proper 
piston to rod clearance easily...serves no real purpose in my mind.

Gary P.

-----Original Message----- 
From: Daniel McCormack
Sent: Monday, April 08, 2013 5:55 PM
To: 1962to1965mopars@xxxxxxxxxxxxxxxx
Subject: RE: master cylinder?

I've never been able to find a replacement for that rubber piece but you can
cut one from a piece of vacuum hose. Don't remember the exact size but use a
hose with the same inside dia. As the outside dia. Of the groove in the
brake rod.


-----Original Message-----
From: 1962to1965mopars@xxxxxxxxxxxxxxxx
[mailto:1962to1965mopars@xxxxxxxxxxxxxxxx] On Behalf Of Gary H.
Sent: Monday, April 08, 2013 8:40 PM
To: 1962to1965mopars@xxxxxxxxxxxxxxxx
Subject: RE: master cylinder?

No change that I recall. Someone else may chime in if I am in error.

The brake rod is sometimes troublesome to remove from the single reservoir
version.

BTW, anyone know if the rubber piece that holds the rod in place reproduced
now? At one time it was difficult to find.

Thanks,
Gary H.

>  -------Original Message-------
>  Gary - any change needed to the 65's brake pedal?  Will the 67 master
>  cylinder bolt right in?  Bob from Maine
>
>  -----Original Message-----
>  Pretend your '65 is a 1967 B Body and go from there in your parts search.
>  New, not rebuilt, is preferred by many.
>
>  Thanks,
>  Gary H.
>
>  >  -------Original Message-------
>
>  >  I plan on going to a dual master cylinder,  with drum brakes, front
>  > and  rear, on my '65  Coronet.  Is there a certain  one to use?
>  > Thanks, Warren
>


-- 
-- 
--
Please address private email -- email of interest to only one person --  
directly to that person. That is, email your parts/car transactions and 
negotiations, as well as other personal messages, only to the intended 
recipient. Do not just press "reply" and send your email to everyone using 
the general '62-'65 Clubhouse public email address. This practice will 
protect your privacy, reduce the total volume of mail and fine-tune the 
content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and 
http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups 
"The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

--- 
You received this message because you are subscribed to the Google Groups 
"The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an 
email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.

-- 
-- 
--
Please address private email -- email of interest to only one person --
directly to that person. That is, email your parts/car transactions and
negotiations, as well as other personal messages, only to the intended
recipient. Do not just press "reply" and send your email to everyone using
the general '62-'65 Clubhouse public email address. This practice will
protect your privacy, reduce the total volume of mail and fine-tune the
content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and
http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups
"The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

--- 
You received this message because you are subscribed to the Google Groups
"The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an
email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.


-- 
-- 
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

--- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.